Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (May 2000, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 3 May 2000 08:39:47 -0700
Reply-To:     Karl Wolz <wolzphoto@WORLDNET.ATT.NET>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Karl Wolz <wolzphoto@WORLDNET.ATT.NET>
Subject:      Re: Power Steering: leak and pressure switch ?
Comments: To: k1cajun@PIPELINE.COM

First, look for any hose clamp type fittings that could be tightened. BTDT

The power steering draws power from the engine. When you are at idle and the steering is locked over, if the idle isn't raised a bit, the engine might stall.

Karl Wolz ----- Original Message ----- From: "Dave L" <k1cajun@PIPELINE.COM> To: <vanagon@GERRY.VANAGON.COM> Sent: Tuesday, May 02, 2000 1:16 PM Subject: Power Steering: leak and pressure switch ?

> On the return leg of the first road trip since our 89 Westy got a new > VW reman engine, it was raining and the rear wiper wasn't doing a > good job of keeping window clear (new blade too). It was nighttime > and a Westy, so rear window wasn't useful anyway. But on the last > gas stop, I went to squeegee the glass and found the rear door was > coated with oil and there was a drip on muffler, motor mount bar, and > right head! Oil was blowing back due to the finely tuned aerodynamics > of the Vanagon body. Oil level wasn't down by much, so I drove it > the rest of the way home and two days later, to the dealer. They > found it was a power steering leak and said the oil was down due to > normal oil usage when seating rings. (I did first oil change at 700 > miles, second at 2000). That was good news! I said I can handle > that repair and took it home. > > Now, looking it over, I see the pump and the send/return lines > fittings are definitely coated all around with oil. I want to spray > clean it all off with some degreaser, drive it a bit, and see if the > leak is at the seal between the two sides of the pump housing, the > shaft seal, or the send/return fittings. If it's the housing or shaft > seal, it looks easy to rebuild. Kits available at dealer for $30. > > Or maybe they didn't replace the send/return fittings' sealing rings > when the pump was off to replace engine (if they even disconnected > the lines that is). > > So I wonder: > > 1) What kind of degreaser is safe to use - I'm hesitant because of > the fat rubber head gaskets. I don't want to use anything that > might damage anything on the waterboxer. > 2) The Bentley says to use new seal rings on the lines. Anyone ever > really do this ? They appear to be a metal ring, not rubber. > 3) The Bentley says to use tool VW681 to remove old shaft seal. Will > a special tool really be necessary ? If so, I guess I'll just use > a rebuilt pump. But it would be nice to save the bucks and have > the pleasure of doing it myself, as long as it's not masochistic! > 4) There are wires at the end of the high-pressure line, like for a > sending unit. Bentley doesn't show it in the steering chapter, > but electrical diagram on 97.125 shows a PS pressure switch. I > don't recall a dummy light for the PS on the dash ?! And the > diagram shows it wired to the Digifant control unit relay and the > idle stabilizer control unit. Why is the PS wired to the FI ? If > you lose PS pressure, does it make you slow down ? > > Dave L. > 89 Westy > 87 Vanagon


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.