Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (September 2000, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 6 Sep 2000 08:09:48 -0700
Reply-To:     John-Reed Maffeo <rlpa80@EMAIL.SPS.MOT.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         John-Reed Maffeo <rlpa80@EMAIL.SPS.MOT.COM>
Organization: Motorola Semiconductor Products Sector
Subject:      Re: Emission / Air Mass Sensor - could it be the cause?
Comments: To: Wolfgang Ziegler <ziegler@PRINCETON.WIRELINE.SLB.COM>
Content-Type: text/plain; charset=us-ascii

> > Subject: > Emission / Air Mass Sensor - could it be the cause? > Date: > Tue, 5 Sep 2000 17:22:12 -0400 > From: > Wolfgang Ziegler <ziegler@PRINCETON.WIRELINE.SLB.COM> > > > > Hi, > I am new to the list - thanks for helping me out. I searched the archives and found some valuable hints. > Have been facing an increasing problem with my 88 Vanagon (106 kmiles) over several months now: > Symptoms: > Very little power, sluggish when below 2000 rpm, especially in warm climate and/or with AC on > Very high idle emissions (HC close to 1000 - CO 1%), prev. years <100 > No performance problems with O2 sensor disconnected (HC close to 1000) > > Steps taken: > clean and reseat all connections: ECU, sensors, Idle control... > new sparks, wires, distributor, air filter - timing tuneup > new temp sensor, O2 sensor > check for vacuum leaks, check idle control valve > > Suspects: > The resistive layer of the air mass sensor shows wear by the wiper. The 'over-all' impedance is about 300 Ohms (as defined by the > individual resistors), when measured on the wiper (analog meter) I see the values between 25 (closed) and 300 (open) vary all over the > place - not monotonously increasing. Is this because of the high impedance of the black conductor or is the unit faulty? What should the > reading be for the idle position (1/3 open)? > > Will a new unit require major adjustment - have not seen anything on a how-to > > What is the correct procedure to adjust timing for the Digifant system? - engine warm up - disconnect temp sensor - adjust at 900 rpm? > > I appreciate your help - need to get through inspection soon.

Wolfgang,

Your experience sounds very similar to mine. I did not pass Arizona emissions until I replaced my AFM. I got one from Bus Depot, dropped it in and breezed through the tests.

I still have my old one if anyone is interested in it for any reason.

> > Wolfgang Ziegler

John-Reed Maffeo- '86 Syncro Glacee (for Sale:( Mesa/Chicago/Dallas


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.