Date: Mon, 25 Sep 2000 00:09:40 -0300
Reply-To: Jean-Guy Savoie <jgsavoie@NBNET.NB.CA>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Jean-Guy Savoie <jgsavoie@NBNET.NB.CA>
Subject: Re: coolant change
Content-Type: text/plain; charset="iso-8859-1"
No you don't have to pinch hoses, as far as I can see. I think bently is
specifying a special proceedure for engine removal or some such thing. It
is confusing and the archives have discussed this before.
search the archives for "coolant change" and you will get numerous hits.
These one's suggest another method:
http://gerry.vanagon.com/cgi-bin/wa.exe?A2=ind0008D&L=vanagon&P=R20441
http://gerry.vanagon.com/cgi-bin/wa.exe?A2=ind0008D&L=vanagon&P=R22084
http://gerry.vanagon.com/cgi-bin/wa.exe?A2=ind0008D&L=vanagon&P=R20730
(back end of the bus way up???)
There are excellent posts on the conventional method also, namely on by
Michael Modl:
"Here is the simple version to flushing the coolant. Remove the right
sheild
on the right cylinder head to access the drain plug. Drain the coolant. It's
not needed to do the same on the left cylinder head drain because only about
half a quart of coolant will come out on the left side when the cooling
system
is drained. Remove the spare tire. Remove the lower radiator hose and drain
the rest of the coolant. Reinstall the hose. Put right cylinder head sheild
and drain plug back on. Add VW phosphate free coolant already premixed with
50% water and 50% coolant to the coolant reseviour in the left side of the
engine compartment. Jack the front end of the car up about 12 inches. Remove
the headlight grill. Start car. Open up the bleeder screw on top of the
radiator, don't remove the bleeder screw. It's on the top right while
looking
at the radiator. Make sure the car was in neutrul and the E-brake is on.
Open
up the bleeder screw on the thermostat housing on the front left part of the
engine compartment. Coolant doesn't come out of this bleeder screw. It
internally bleeds. Hold engine RPM at around 3500 to 4000 RPM. Add coolant
ALL
the way full while holding high RPM. You'll notice the higher the RPM, the
more coolant you can add. Put the coolant resevior cap on. Now let go of the
throttle, let the car idle. Doen't worry about that hose that goes on the
cap
just yet. Go up front to the bleeder screw and see if any air is coming out.
When a small steady stream of coolant comes out with no air bubbles, close
the
bleeder screw. Go back to the coolant resevior, raise RPM way up again to
around 4000 RPM. Unscrew cap. Add as much coolant as full as you can, raise
RPM even higher to get as much as you can in. Put resevior cap back on and
now let go of the throttle, let the car idle. Go back up front to the
bleeder
screw, open up a little bit to get any remaining air out. Close when
comfirmed. Put that hose on the coolant resevior. Let the car idle till hot
and the fan has cycled once. One more quick check of the front bleeder
screw.
Close the rear bleeder screw. Turn the car off to reset the flashing
coolant
light. Put the other things back together. You'll have used allmost two
gallons of PREMIXED coolant. Do with a cold engine. The adding coolant and
going back and forth, should take about 5 minutes, before waiting to reach
operating temp. Do not remove the coolant resevoir cap with a hot engine.
Fill the coolant catch behing the lisence plate. The whole job is a little
messy. GOOD LUCK. Let me know how it works out."
----- Original Message -----
From: Alan Compher <alanncee@YAHOO.COM>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Sunday, September 24, 2000 8:19 PM
> Need some advice please!
> I am the new owner of a 91 Vanagon 2.1L, auto. Can
> someone please advise as to the proper way to
> drain/refill coolant? Have Bently manual, but it seems
> to say that it involves clamping different hoses,
> draining from drains under cylinders...Can't I just
> undo the hoses at the bottom of the radiator?
> Any advice would be appreciated! Thanks
>
> __________________________________________________
> Do You Yahoo!?
> Send instant messages & get email alerts with Yahoo! Messenger.
> http://im.yahoo.com/
>