Date: Wed, 24 Jan 2001 23:35:44 -0500
Reply-To: Dennis Haynes <dhaynes@OPTONLINE.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Dennis Haynes <dhaynes@OPTONLINE.NET>
Subject: Re: Crankshaft Endplay Adjustment Hits Me Flat
In-Reply-To: <20010124.211227.6815.3.kdlewis@juno.com>
Content-Type: text/plain; charset="iso-8859-1"
Derek,
The correct play is between .004" and .006". Note the extra 0. When the play
is excessive, you will feel it go thunk as you move the flywheel. If the
play was set too tight, after 80,000 miles it is now worn in. Leave it be
Dennis
-----Original Message-----
From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com]On Behalf
Of kenneth d lewis
Sent: Wednesday, January 24, 2001 9:07 PM
To: vanagon@GERRY.VANAGON.COM
Subject: Re: Crankshaft Endplay Adjustment Hits Me Flat
Derek;
Good question. I also have experienced your dilemma. I think the
secret is not to flex the flywheel. Place the screw drivers at right
angles to the gauge. This way, in my mind, the flexing will be least at
the gauge.
My preferred method is to assemble the crank dry (out of the
engine i.e. on the work bench) with thrust bearing, shims, etc and torque
it down. Then see which is the largest feeler gauge that will fit
between the shims (this is your endplay). Do the math and swap shims if
neccesary.
Drive Safely & Good Luck
Ken Lewis <Kernersville,NC>
86 VW crewcab;60 356B Coupe
--------------------------------------------------
On Wed, 24 Jan 2001 15:28:18 -0500 Derek Drew <derekdrew@RCN.COM> writes:
>While I was changing the clutch I decided to check the crankshaft
>endplay
>to see if it was in spec.
>
>There is an excellent post in the archives on this topic by, I think,
>Andrew Martin (agmartin@silverlink.net although he was posting from a
>different address at the time).
>
>The thing is that I found that I could not get any measurement during
>this
>process in which I had any confidence.
>
>My procedure was to pound the flywheel as far back as it would go with
>a
>huge rubber hammer and then stick screw drivers under the flywheel at
>opposite sides and try to pry the flywheel toward me (toward the front
>of
>the vehicle). I measured the distance that the fllywheel traveled.
>What I
>found was that the flywheel would travel any amount depending on how
>hard I
>pry'd with the screwdrivers. I could easily make it travel 0.04" or
>0.10"
>or if I pried really hard I went further.
>
>Once I released my screwdrivers the crankshaft went back to within
>0.01" of
>where it had been at the start. It is supposed to be 0.04" plus or
>minus
>0.01" if I read the manual correctly.
>
>This is a new factory engine in a 90 syncro with about 80,000 miles on
>it.
>
>So I either have a crankshaft endplay that is too tight or I have one
>that
>is too loose.
>
>I called Dennis Haynes on the phone about this and he spoke with the
>voice
>of authority: "Just leave it. It sounds like it was good and tight.
>That's
>good. When there is trouble is when it is too loose. Don't mess around
>with
>it."
>
>But I am still drumming my fingers a little. What if I actually have
>only
>0.01" of play ? when the spec calls for 0.04."
>
>I was thinking that possibly the trouble was that I used a layer of
>grease
>to make the shims tacky and so they would stick on there while I put
>the
>flywheel back on.
>
>Does anybody think this layer of grease was a mistake and could be
>throwing
>the adjustment off? Should I take them out and wipe them off and use
>oil
>and put the whole thing back together? 81 foot lbs. on the flywheel
>bolts
>enough to squeese the grease out of the shims?
>
>The manual said to use oil, I noticed later.
>
>Comments from the knowledgeable please.
>
>Any reason I shouldn't just bolt the transmission back on and ignore
>this?
>
>_______________________________________________
>Derek Drew New York, NY
>CEO & Co-Founder
>http://www.ConsumerSearch.com/
>===========================
>"Best Expert Review Site"
>for product reviews on the Internet
>Jan. 2001, PC World Magazine
>==========================
>80 South Street, 2nd Floor
>New York, NY 10038
>derekdrew@rcn.com
>212-580-6486
>
>Alternate numbers for the industrious phone caller that wants to try
>every
>avenue: 917-848-6425 (cell); 202-966-7907 (Work), 212-580-4459 (Home),
>202-966-0938 (Home), 978-359-8533 (fax [efax]), 212-269-3188 (Seaport
>office), 212-269-3188 (Seaport main number).
________________________________________________________________
GET INTERNET ACCESS FROM JUNO!
Juno offers FREE or PREMIUM Internet access for less!
Join Juno today! For your FREE software, visit:
http://dl.www.juno.com/get/tagj.
|