Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (February 2001, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sun, 25 Feb 2001 12:48:14 -0700
Reply-To:     Karl Wolz <wolzphoto@WORLDNET.ATT.NET>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Karl Wolz <wolzphoto@WORLDNET.ATT.NET>
Subject:      Re: Odometer Repair-Migrating Shaft
Comments: To: "Thomas D. Hanlon" <hanran@EARTHINK.NET>

If I understand your description correctly, my fix was:

I used a small (6mm or so) socket to tap the gear back in place so it was again meshing. I then took a pair of side-cutters and put a slight crimp in the shaft. The gear no longer walked off the shaft.

It isn't that the gear is wobbly loose, so much as it constantly gets pressured to move in one direction and eventually will do so.

Karl Wolz

----- Original Message ----- From: "Thomas D. Hanlon" <hanran@EARTHINK.NET> To: <vanagon@GERRY.VANAGON.COM> Sent: Sunday, February 25, 2001 10:48 AM Subject: Odometer Repair-Migrating Shaft

> Listees, > > I've removed the speedometer from my 84 Westy to evaluate a non-working > odometer. Upon removal of the unit from the case, I find that the shaft > on which is mounted the (beige) gear-which drives the odometer-shifts to > the left and disengages from the (white) gear which drives the (red) > worm gear. > > The beige gear is not loose on the shaft, a condition/problem which I > expected to find and about which much has been written on solving by > roughing the shaft, or using "Super Glue," and other suggestions. There > is not evident any connector or fastener which I would presume retained > the shaft to the mechanism. I conjecture that a "c" clip of some kind > would have been used. Not there or in the bottom of the speedometer > casing. > > For a "bench test," I have used a modified shaft (a nail Dremeled to > the dimensions of the cable end) to perform the speedometer cables' > function to turn the gears. I fastened the "shaft" to an electric drill > set at "reverse" to drive those gears which drive the road speed needle, > the odometer numbers and the mileage numbers. > > The shaft migrates to the left (facing the frontispiece) enough to > disengage the odometer gears. The speed needle continues to operate but > the mileage numbers stall, too. > > I've attempted to find 3m x 60 centimeter stainless rod, or even bolts, > with which to replace the shaft. No luck in any of the hardware stores > in my locale. Any sources or suggestions? > > Can anyone offer diagnoses and solutions? > > Tom Hanlon > Palm Springs, CA > 84 Westy >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.