Date: Fri, 29 Jun 2001 12:53:00 -0700
Reply-To: Karl Wolz <wolzphoto@WORLDNET.ATT.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Karl Wolz <wolzphoto@WORLDNET.ATT.NET>
Subject: Re: Oil pressure switch
Leon,
It was I who originally posted this question.
.3 bar, or actually mine are labeled .15 - .45 (tolerance?) are used on all
low pressure systems, to the best of my knowledge. I have one in my '84 and
one on my '85 (both 1.9s at this point). I also have one on the low
pressure side in my '88.
Here's where it gets sticky. I bought the '88 with the engine in the back
seat. It was all there except the high pressure switch. I wandered over to
my FLIAPS (I = Import) and asked for a high side switch, and was given a 1.8
bar switch, which I promptly installed. At around 2500 rpm, the light lit
up and the buzzer buzzed.
Hmpph!
Call previous owner. "Any oil pressure problems in the past?"
"No, never."
Guy seemed pretty honest (that's why I bought the van from him plus a great
price), so I've accepted this as a given.
Look in the Bentley, and sure enough, Bentley calls for a 1.8 switch.
"Must be defective!", says I, so I go and buy another one (at only $3.50, I
can afford two). I install the new switch and voila, the SOB still buzzes.
To myself, I am now calling the DPO a freaking liar.
I take the van up to my local friendly mechanic, and he screws in a pressure
gauge. We run the engine for a while, and while the pressure seems a bit
low, it does not seem to be disastrously so (18 psi @ 2200 rpm). We throw
in a can of Bardahl. Takes like, fifteen minutes to flow into the engine.
OP comes up about ten points and the buzzer stops buzzing. I'm still not
happy. I no longer hear a real buzzer, but one is still going off in my
head.
Got home last night and started looking at the vanagon.com website under
technical, or whatever the heading says. Find articles on oil pressure.
Reading through them, they all describe what I've gone through. I'm just
about ready to quit, when I get to the last article, which describes pretty
much the same thing, except that this article mentions a .9 bar switch!
With excitement, I go to the BD website and look up 2.1 OP switches to see
which one Ron carries. Damn! He stocks both of them!
It's time to seek the wisdom of the list, so I write to Gerry and implore
the membership to shed some illumination on my dilemma. The first three
responses I get say "0.9bar", "1.8bar", and "I dunno, but that 's a good
question".
It's now twelve hours since I posted my original question, and no one has
actually written back and given me a definitive answer on the subject,
though, from what I've hear so far, I'm gonna go find a .9bar switch pronto.
Karl
----- Original Message -----
From: "Leon Korkin" <korkwood@SURFREE.COM>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Friday, June 29, 2001 10:06 AM
Subject: Re: Oil pressure switch
> If you got 86 and later Vanagon you got 2 oil pressure switches, .9 and .3
bar.
> working in dynamic oil pressure system. .3bar switch works at lower rpm
and .9
> bar switch works at 2000rpm and higher according to tach signal. 1.8 bar
was
> used on 85 model only
> Leon
> 85 Subwagen Westy
>
> Dennis Haynes wrote:
>
> > The 1.8 bar switch is too high for the Vanagon. It will cause nuisance
> > sounding of the buzzer above 2500 rpm.
> >
> > Dennis
> >
> > -----Original Message-----
> > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com]On Behalf
> > Of Karl Wolz
> > Sent: Friday, June 29, 2001 2:57 AM
> > To: vanagon@GERRY.VANAGON.COM
> > Subject: Oil pressure switch
> >
> > Hi all,
> >
> > BD lists two oil pressure switches for the "back of the engine". One at
.9
> > bar and the other at 1.8 bar. What are the different applications for
these
> > two switches?
> >
> > The article by Jim Davis on the vanagon.com page mentions the 0.9 switch
as
> > being the correct one. I was sold a 1.8, and am going nuts trying to
track
> > down an oil pressure problem that may not actually exist!
> >
> > Thanks,
> >
> > Karl Wolz
>
|