Date: Thu, 12 Jul 2001 13:34:51 -0700
Reply-To: Karl Wolz <wolzphoto@WORLDNET.ATT.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Karl Wolz <wolzphoto@WORLDNET.ATT.NET>
Subject: Re: 86 vanagon Oil Pressure Switch
Yeah. Once you've done it three times n a week, it's real easy!
Grab yourself a 13mm wrench and take of the water pump pulley. If you do
this, you've got pretty easy access to the sender. The job is about 8000%
easier if you use the correct tool, which is a deep well 24mm socket.
Easiest is to put the socket on the sender and then put the wrench on the
socket. Due to space limitations, you're better off using a breaker bar
instead of a ratchet.
Once you've loosened it a bit, it should only be finger tight and an easy
turn off. Some say you need to use a screwdriver to push the sheet metal
out of the way, but I didn't really need to do that.
Karl
----- Original Message -----
From: "clerkin" <clerkin@STUDENTS.UIUC.EDU>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Thursday, July 12, 2001 12:28 PM
Subject: Re: 86 vanagon Oil Pressure Switch
> Well I got the right switch (the gray one) but I can't seem to figure out
> where it goes. Do you access it from above or below? There seems to be
some
> sheet metal that I cannot get out of the way to get to the switch. Any
ideas?
>
> Thanks,
> Patrick
>
> >===== Original Message From Karl Wolz <wolzphoto@WORLDNET.ATT.NET> =====
> >Hi Patrick,
> >
> >You're dealing with two different animals here.
> >
> >The gauge sending unit screws into the low pressure outlet (.3bar). The
> >1.8/.9 bar switch screws into the high pressure outlet, which is located
to
> >the left of the main pulley and under the water pump. Installing the
gauge
> >unit will not make your buzzer stop. You need to pick up a .9bar sender
and
> >replace the 1.8 bar with it.
> >
> >Karl Wolz
> >
> >----- Original Message -----
> >From: "clerkin" <clerkin@STUDENTS.UIUC.EDU>
> >To: <vanagon@GERRY.VANAGON.COM>
> >Sent: Monday, July 09, 2001 4:34 PM
> >Subject: 86 vanagon Oil Pressure Switch
> >
> >
> >> I have a 1986 vanagon with an oil pressure light and buzzer which comes
on
> >> when the vehicle is warmed up and is above 2000 rpm. It will also go
out
> >> around 3500 rpm. The engine was rebuilt about 30k ago and the light
came
> >on
> >> immediately. When the mechanic was called about the problem, he said
that
> >he
> >> must have put the wrong oil pressure switch in. It has been run like
this
> >for
> >> 30k without any problems, but I want to fix the problem (better late
than
> >> never.) I decided to upgrade to a VDO guage and sender from the Bus
> >Depot,
> >> but the guy I talked to on the phone didn't seem like he had any idea
what
> >was
> >> going on. He told me that they did not sell the stock switch, and that
> >the
> >> only thing they had was the VDO switch and guage. He also told me that
> >their
> >> VDO guage is not the dual guage (allowing both the idiot light and
guage
> >to
> >> operate) which is in contradiction to their website. In checking their
> >> website I have found both of these statements to be false, but in their
> >> defense, the man said Ron was gone and would return in a few days. He
> >said I
> >> should call him about any specific questions. Since I am still unable
to
> >get
> >> any answers at the Bus Depot I thought I would try the list.
> >>
> >> 1. Is the dual VDO guage set at .9 or 1.8 bar?
> >> 2. Is it normal for an engine with the improper switch to flash it's
> >idiot
> >> light?
> >>
> >>
> >> Thanks,
> >> Patrick
> >>
|