Date: Tue, 18 Sep 2001 09:25:45 +0000
Reply-To: Alistair Bell <albell@UVIC.CA>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Alistair Bell <albell@UVIC.CA>
Subject: Re: Digifant II 'Diesel' Conversion Pics
In-Reply-To: <AIEFIGCNNANNIHLNFBPEKEHHDPAA.vanagon@volkswagen.org>
Content-type: text/plain; charset="US-ASCII"
David,
A couple of observations/questions...
Why not use the stock manifold? You have to bash the body panels in anycase,
and have the throttle valve at the rear of the engine. Save you the bother
of the manifold work and leading the sewer pipe intake around the front of
the compartment. Having the throttle at the rear also makes connection to
the stock diesel accel cable straitforward and allows easier access for
maintainance, adjustment of the switches etc.
The K&N filter is in the same approx area of the engine compartment as mine,
except your intake pipe does obstruct oil filter changes a bit...every bit
of access is appreciated when changing the filter, even with the VW doodad
that cradles the filter, its hard to not spill a bit of oil!.
I have noticed a couple of issues with the filter in this position. One is
there is no provision for air pre-heat. While it is not a big deal here in
Victoria (fuel consumption and warm-up times suffer only a little bit), In
colder parts of the country this could be a problem. Also, paradoxically,
even with the heatshield this can be a hot part of the the engine
compartment, peformance oughto suffer in the summer. My friend with a pretty
well identical to mine conversion, moved the battery up to the wasserboxer
stock location and used an A2 airbox (with k&N filter element) mounted
infront of the pass. side tailights. With a little bit of a snorkel he has a
set-up that draws cool air.
The unshrouded K&N filters do make the engine sound louder.
I don't like the position of the ECU. Unless you have blocked off the vents
on that side, water and snow will end up on the ECU. Mine is mounted inside
the van, under the back seat. Maybe not the best for camping storage, but it
is a nicer enviroment!
Its handy having that fuel filter bracket to mount the coil on, isn't it?
Perhaps the best thing about the diesel mounting angle is no fooling around
with bulges/bubbles/cakepans on the engine hatch!
Alistair
albell@uvic.ca
'82 Westy, diesel=>I4 gas
/"\ ASCII Ribbon Campaign
\ / No HTML/RTF in email
X No Word docs in email
/ \ Respect Open Standards!
on 18/9/01 5:05 AM, David Marshall at vanagon@VOLKSWAGEN.ORG wrote:
> I just uploaded some pictures of an installation I did to a customers 1982
> Diesel Westfalia. Out goes the 48hp Diesel and in goes a 105hp Digifant II
> motor (ok... time to do the Tim Allen rant!). Quite the installation and I
> must say that my 15 degree kits are much easier to do than the Diesel setup!
> The biggest challenge is the intake manifold and intake system - there is
> NOTHING out there, that is available in North America or Europe that will
> fit without doing some sort of modification to the side wall of the engine
> bay. Good to see VWSA has a custom cast intake system for their I4
> conversions. We used a 1981 Rabbit intake manifold that we removed some
> material from to it wouldn't interfere as much with the side wall. We still
> had to take a ballpien hammer to a 3x6" area on the side wall just above the
> frame rail and dent it in two inches so nothing would interfere. A bit of
> paint and some rust proofing took care of the damage on the side wall,
> although I don't think the customer is totally happy we had to do this. We
> used the original Digifant II throttle valve and installed it 'upside down'
> so everything would line up right - the vacuum lines for the fuel pressure
> regulator and the line for the frequency valve would be hitting the side
> wall if it were installed the right way up. This also meant doing some
> welding and grinding to the intake manifold so we could open the mouth of it
> large enough for the A2 series valve to function correctly. The rest of the
> intake system was fabricated with a lot of time and thinking... it resulted
> in a very clean looking ABS plastic intake system and a K+N air filter
> mounted on a custom bracket that fits on top of the water pump - once the
> heat shield is in place it will make a very nice installation as everything
> moves with the engine. The wiring harness was pretty uneventful as this is
> the umpteenth time I have made a 'plug and play' Digifant II wiring harness.
> Besides running a wire to the battery terminal the wiring harness was a
> 'plug and play' event with only three seconds of cranking to get the engine
> running the first time! Warning - make sure no one is asleep when you fire
> up an I4 engine with only an exhaust manifold installed as it is a tad bit
> on the loud side! :)
>
> Pictures can be seen at
> http://www.fastforward.ca/vanagonswap/dieselparts.htm for those who are
> interested.
>
> Any questions??? Feel free to ask!
>
> David Marshall
>
> Fast Forward Automotive Inc.
> 4356 Quesnel Hixon Road
> Quesnel BC Canada V2J 6Z3
> mailto:info@fastforward.ca <mailto:info@fastforward.ca>
> http://www.fastforward.ca <http://www.fastforward.ca>
> Phone: (250) 992 7775 FAX: (250) 992 1160
>
> . Vanagon Accessories and Engine Conversions
> . Transporter, Unimog and Iltis Sales
> . European Lighting for most Audi and Volkswagen models
>