Date: Wed, 24 Oct 2001 11:08:12 -0500
Reply-To: John Rodgers <jhrodgers@CHARTER.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: John Rodgers <jhrodgers@CHARTER.NET>
Subject: Re: Re; Undercoating, and Bed Liner etc.
Content-Type: text/plain; charset=us-ascii
I'm getting ready to apply poly-urea liner material to the exterior of my
van in strategic places. Poly-urea is a second generation material that is
the competitor to polyurethanes. Can be applied over a puddle of water and
it will set. Polyurethanes under those conditions would rise and swell like
bread dough. Urethanes used in expanded foams utilize water to get the
expansion.
As for my van, it is red, or actually burgandy, in color. The front end and
the rocker panels along the bottom edge have really taken a beating from
rocks and gravel. I plan to apply approximately a 1/8 th inch black
coating on the front end and the rockers. On the rockers it would come up to
the height of the fiberglas wrap-a-round bumpers that are on the GL. This
material is incredibly tough, yet flexible, and should provide considerable
rock protection. Preparation is to scuff the surface well the apply.
I had not thought of the wheel well and undercoating possibilities. I am
going to take a long hard look at those possibilities as well. With proper
preparation, I would think this product, or others similar would protect and
prolong the life of the vehicle by preventing/reducing rust by preventing
the entrapment of water, salt, etc. Of course if you live in the northern
climes as I did for many years, nothing beats a good hose job with a high
pressure wand at the local car wash to remove the salt/sand/crap that
accumulates in winter. This poly -urea is applied at a pressure of
approximately 2500 psi and sets in 8 seconds. Currently my son runs an
operation using it for liner applications and roofing membranes on
buildings. Pretty versatile stuff.
This is the same material that the auto industry is using to make the
flexible bumpers, fenders, splash pans, etc, that are found on modern cars.
John Rodgers
88 GL Driver
Terry Kay wrote:
> Malcom,
>
> I used the urethane bed liner on the bottom of my Van in 90 degree heat,
> so I'm sure it was dry, and there are zero holes anywhere.
> Anyone who applies any kind of finish when the surface is wet is nut's.
>
> Bedliner is urethane based product, not asphalt or tar.
>
> This oiling of the interior panels is OK, and I have used drained gear
> oil, on other vehicles, with great sucess.
>
> Cosmoline is the ultimate answer-----
> Bed liner on top of outer panels ( wheel wells etc.) is excellent too.
> In a matter of fact, Rino Hyde bed liner's advertise the use of their
> product for undercoating as well as an exterior finish---go figure !
>
> Malcolm Stebbins wrote;
>
> Subject: Re: Another rust hot spot
>
> I've been told to be VERY careful of the spray cans of
> tar/asphalt/bedliner etc. When sprayed on new-good, painted service they
> can be wonderful, but when sprayed on old, partly rusted (and perhaps
> moist) surfaces (wheelwells of vanagons) they can actually trap moisture
> in behind the coating and then you will not see the rusting out parts
> till the whole thing falls apart. If one can get the area DRY and wire
> brush off most of the surface rust, then paint the area with "rust
> converter", then paint with rust--inhibiting paint, then top coat, then
> your rubberized bed-liner stuff, you might have a chance, but one can
> not get up in the seams/joints and that is where the Krown (oily)
> rust-inhibitor stuff works very well, it wicks up into all of the
> crevices and forms a barrier against the moisture. IMHO it is a well
> spent CDN$110/year. For all who live along the CDN border, it is a
> worthwhile annual trek. Malcolm (Halifax) On 23 Oct 2001, at 0:29, Terry
> Kay wrote: Roy and other's----
> I have found that if you had purchased several spray cans of black
> urethane rubberized bed liner, and applied several heavy coats of it to
> the mentioned problimatic area's, the rust problem would have been
> drasticly curtailed.
> I blew this stuff into the wheel well's, on the lower rocker seams, and
> the panel under the front bumper two years ago, and it is all still rust
> free.
> Another proven example of better living through chemicals.:>) Later,
> ________
> |[ ] [ ] [ ]\
>
> | | | |
> ~~~ ~||-(())----(())-|
> Terry--
> 74 Campmobile- (Clementine)
> 85 GL- (Delilah)
> 86 BMW 325 ES- (Eva)
> ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ "In life, it is much better to
> want
> something you cannot have---
> Than to have something you can't get rid of"
> (T.K.)
|