Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (November 2001, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 22 Nov 2001 08:22:36 EST
Reply-To:     BenTbtstr8@AOL.COM
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Ben T <BenTbtstr8@AOL.COM>
Subject:      Re: [vanagon] Re: TIICO vs. CA
Comments: To: killer_jupiter@HOTMAIL.COM
Content-Type: text/plain; charset="US-ASCII"

In a message dated 11/21/01 3:25:02 PM Pacific Standard Time, killer_jupiter@HOTMAIL.COM writes:

<< Where's BenT when you need him? >>

OK, Timmy. I was trying to stay out of this one. Most engine swaps are certifiable in the State of California whether it is Eurospec, Tiico, Kennedy or Homemade-O. You just have to make sure you folow the guidelines provided by the California Bureau of Automotive Repair. Most referees are auto enthusiasts like us. Well, at least they are in my end on the State. I had one refreee even advise me on what 911 engine case to base my engine on so that there will be less requirements.

Anyway, for those so inclined, you can read the BAR guidelines on engine swaps below:

------------------------------------------------------------------------------ - Engine Replacement and Rebuilding Guidelines

Overview Engine changes continue to present problems and challenges to car owners and technicians. Here are some tips to keep you and your customers on the straight and narrow.

Our recommendation is to rebuild and reinstall the original engine, transmission, and emission control configuration.

When rebuilding an engine, it must be rebuilt to the original equipment specifications. However, if you do decide to change the engine, these guidelines must be observed to ensure that the vehicle will be eligible for smog certification or registration.

Remember, these are guidelines for performing engine changes -- not certification procedures. All exhaust emission controlled vehicles with engine changes must be inspected by an official referee station and must have a Bureau of Automotive Repair (BAR) Vehicle Identification Label affixed to the doorpost.

Remember also, state and federal anti-tampering laws generally prohibit any modification to the vehicle's original emission control system configuration as certified by the manufacturer. And, Section 3362.1 of the California Code of Regulations prohibits any engine change that degrades the effectiveness of a vehicle's emission control system.

California Certification A federal Environmental Protection Agency (EPA) certified (federal or 49-state) engine cannot be used in a vehicle that was originally certified for California.

Certification Standards Make sure the engine and emission control configuration on exhaust - controlled vehicles are certified to the year of the vehicle or newer, and to the same or a more stringent new vehicle certification standard.

Classification Don't mix engine and vehicle classifications which will degrade the emissions certification standards. For example, a heavy-duty engine cannot be installed in a light-duty exhaust-controlled chassis even if they have the same displacement. Non-emissions controlled power plants such as industrial or off-road-use-only engines may not be placed in any exhaust-controlled vehicle.

Computer Controls If a computer-controlled engine is installed in a non-computerized vehicle, the "CHECK ENGINE" light, the Original Equipment Manufacturer (OEM) diagnostic link, and all sensors, switches, and wiring harnesses needed to make the system fully functional must also be installed.

Emission Control Configuration Mixing and matching emission control system components could cause problems and is generally not allowed. Engine and emission control systems must be in an engine-chassis configuration certified by the California Air Resources Board (ARB) or U.S. Environmental Protection Agency (EPA). The engine must meet or exceed the requirements for the year and class of vehicle in which it is installed.

Emission Warranty Voiding the vehicle manufacturer's emission warranty is not allowed.

Engine Modifications No internal or external engine modifications (cams, pistons, intakes, etc.) may be performed unless the parts are ARB-exempted or EPA-certified for use in the installed engine. Use the database on this site to search for aftermarket parts covered by ARB Executive Orders.

Original Equipment The installed engine and host chassis must retain all of their original emission control equipment. Diesel-to-gasoline conversions must have all gasoline engine and chassis emission control systems installed (such as fillpipe restrictor, catalytic converter and evaporative emission system).

Smog Inspection These vehicles must pass a complete smog inspection (visual, functional, and tailpipe).

------------------------------------------------------------------------------

--


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.