Date: Thu, 29 Nov 2001 12:01:10 -0600
Reply-To: Kim G <ppg1@HOTMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Kim G <ppg1@HOTMAIL.COM>
Subject: Re: Missing Exhaust bolts
Content-Type: text/plain; format=flowed
right, but stainless does not rust and that's why I chose stainless, because
I am sure I will have to remove my exhaust sometime in the future, and I do
not want to have to cut all the rusted nuts and bolts.
bye,
kim
>From: "Vanagon Man" <puzerewski@msn.com>
>To: "Kim G" <ppg1@HOTMAIL.COM>, <vanagon@GERRY.VANAGON.COM>
>Subject: Re: Re: Missing Exhaust bolts
>Date: Wed, 28 Nov 2001 16:10:40 -0500
>
>Stainless steel is not stronger than steel. It is more brittle. Stick
>with
>high grade steel fasteners for jobs such as this. Leave stainless for the
>ornamental stuff (screws holding in mirrors, etc)
>
>Adam P
>81 westy (3 of them)
>74 beetle
>73 Transporter (at paint shop!)
>70 Single Cab "Whitey"
>Vanagon Partsmobiles
>----- Original Message -----
>From: "Kim G" <ppg1@HOTMAIL.COM>
>To: <vanagon@GERRY.VANAGON.COM>
>Sent: Wednesday, November 28, 2001 1:52 PM
>Subject: Re: Missing Exhaust bolts
>
>
> > The same thing happened on my van too, after I replaced the exhaust. I
>used
> > all new stainless nuts and bolts w/ anti-seize. It has become habit to
> > check the bolts when I crawl under the van now.
> > Also, my brand new complete exhaust that I installed in May of this year
> > already has 2 broken brackets. Not what I expected when I paid close to
> > $500 for all new exhaust, and it has started to fall apart in 6 months
>time.
> > bye,
> > Kim
> > 85 GL
> >
> >
> > >From: Blake Thornton <thornton@MATH.UTAH.EDU>
> > >Reply-To: Blake Thornton <thornton@MATH.UTAH.EDU>
> > >To: vanagon@GERRY.VANAGON.COM
> > >Subject: Missing Exhaust bolts
> > >Date: Wed, 28 Nov 2001 11:29:26 -0700
> > >
> > >I climbed in my 84 van this morning and turned it on, and boy did it
>sound
> > >rough. I figured it was just cold (it was probably 15 degrees F here
>in
> > >Utah this morning) and I figured the van needed to warm up. Well, it
> > >sounded very rough the whole ride and when I got home I looked
>underneath
> > >and took a look.
> > >
> > >Where the collector pipes (attached to the heads) meet the next pipe
>(the
> > >pipe with the O2 sensor in it), there are four bolts (two for each
>pipe),
> > >and I only had one. Somehow three of the bolts came undone! I put a
>new
> > >exhaust gasket (it was missing where the bolts were missing) and put in
> > >some new bolts, but why did this happen?
> > >
> > >I recently put on a new exhaust system (less then a month ago), and I
>am
> > >fairly sure I tighten everything down good. Just to be sure, I checked
> > >all the exhaust bolts and there were a few that were looser then I
>liked
> > >(so I tightened them up).
> > >
> > >What do you think? Was I careless, or was the heating and cooling
>cycle
> > >on a new exhaust system enough to loosen the bolts? Or was it
>something
> > >else?
> > >
> > >Blake
> >
> >
> > _________________________________________________________________
> > Get your FREE download of MSN Explorer at
>http://explorer.msn.com/intl.asp
> >
>
>
_________________________________________________________________
Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp
|