Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (March 2002, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sun, 24 Mar 2002 17:27:54 +0000
Reply-To:     Mike Finkbiner <mike_l_f@HOTMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Mike Finkbiner <mike_l_f@HOTMAIL.COM>
Subject:      Re: Propane Tank Clean Up
Content-Type: text/plain; format=flowed

Tom said -

<SNIP>

My question - do you have any advice about/procedures for removing a Westy tank, stripping off regulator and valves, removing paint/rust, repainting, and installing new regulator & open/close valve - all without blowing myself into the next State <SNIP>

Tom -

I just went through this with a used tank myself. The other posts have covered most of it.

Rather than sandblasting, I wirebrushed it and used POR-15. Either method should work.

The inside of my tank had a fair bit of rust. The RV guy said that was common, because propane has water in it. I cleaned it up by getting a handful of ball bearings and shaking the tank. Good for the arm muscles!

Then I washed it out with plenty of warm water, rattled it some more, and rinsed again. Once the flashlight showed a pretty clean interior, I got the ball-bearings out through the fill hole. They didn't all want to come out, but I used a piece of stiff plastic from a bubble-pack to make a trough and stuck it in the hole to catch them as they went by.

The bleeder tube was partly plugged, so I ran a piece of stiff wire in there to clean it out.

To get out any remaining rust, I used a product called Super Iron Out (www.ironout.com) which is a powder you mix with water to remove rust stains. It was an experiment, but it seemed to clean up the inside surface pretty well.

One propane web site said that rust inside the tank will absorb the chemical which makes it smell, so I figured a little extra care wouldn't be a bad idea. Also, the RV guy said that in his experience, inside rust is what causes tanks to fail, not outside rust.

After a final rinsing, I let the tank dry out next to the stove. Just before taking it to the RV place where they were going to hook it up, I ran a pint of anhydrous alcohol through it to soak up any last bit of moisture.

My RV place didn't pull a vacuum. They ran propane through it to remove the air, and then filled it up to check for leaks.

One note on paint. I had intended to leave the tank black, but had to paint it white to get it mounted. The code apparently calls for a light color to avoid having the tank absorb heat. Don't know how logical that is, but another coat of paint won't hurt.

Mike Finkbiner '87 Westy Moscow, ID

mike_l_f@hotmail.com

_________________________________________________________________ Get your FREE download of MSN Explorer at http://explorer.msn.com/intl.asp.


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.