Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (May 2002, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Tue, 7 May 2002 10:56:09 -0700
Reply-To:   David Marshall <vanagon@VOLKSWAGEN.ORG>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   David Marshall <vanagon@VOLKSWAGEN.ORG>
Subject:   Re: A damn OS question again, yea!!! now i need some help, it's my turn....
Comments:   To: Ben huot <huotx@VIDEOTRON.CA>
In-Reply-To:   <vanagon%2002050702195815@GERRY.VANAGON.COM>
Content-Type:   text/plain; charset="iso-8859-1"

450mV is 0.45V meaning that you are getting a signal. It is best to measure this with a analog multimeter as most digital ones are too slow to read the always fluctuating output of the O2 sensor. It should be, on a correctly tuned vehicle 700mV plus AND minus 200mV with the average being 700mV.

David Marshall

Fast Forward Automotive Inc. 4356 Quesnel Hixon Road Quesnel BC Canada V2J 6Z3

http://www.fastforward.ca mailto:sales@fastforward.ca Phone: (250) 992 7775 FAX: (250) 992 1160

- Vanagon Accessories and Engine Conversions - Vanagon, Transporter and Iltis Sales and Importation - European Lighting for most Volkswagen models

-----Original Message----- From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com]On Behalf Of Ben huot Sent: May 6, 2002 11:20 PM To: vanagon@GERRY.VANAGON.COM Subject: A damn OS question again, yea!!! now i need some help, it's my turn....

Hi guys, i receive my new Oxygen Sensor today

but i don't see any difference with the old one!!!!

One question:

Many people are saying that an OS produce voltage when hot and unplug!!!! Between 0.1 to 1 volt. (rich mixture or poor mixture)!!!!!!!!!!!!!!!!! For now I don't agree!!!

Should I unplug the battery to reset the ECU?

Explanation: I get the van too normal operating temperature (OS is plug); I unplug the OS and test voltage to this one (ground the negative and I touch the OS sender wire with the positive of the voltmeter); I get about 450MV (it means no reading), I never get .1 to 1 volt. If i touch the van side of the OS wire only I get a steady .5 Volt when the OS is unplug. When i plug back the OS (Van running and hot) it get down to 450MV or so but sometime it give me a brief .7 volt and it goes back very fast to .350MV or no reading!!!!!. (back and forward) I never get a steady reading; yes my voltmeter wires are well attached.

What are your suggestions?

Best regards, Ben http://www3.sympatico.ca/huotx/engine1.htm

Ps: I have 2 new OS sender (error from the company) and the old one, they all give me the same reading!!! Is my $100 voltmeter faulty!!!!


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.