Date: Tue, 9 Jul 2002 22:57:46 -0500
Reply-To: Marshall <mjruskin@SHAW.CA>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Marshall <mjruskin@SHAW.CA>
Subject: Part 1 of 2: Dual Air Conditioning in a Vanagon
Content-type: text/plain; charset=iso-8859-1
Hi Volks:
This is how you add a front ac to a Vanagon.
I have another email from the same gent who provides some further insight.
It's posted next.
Marshall Ruskin
84 Westy, "Trip-wrecker"
----- Original Message -----
From: "Ed McLean" <email99@BELLSOUTH.NET>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Tuesday, November 13, 2001 11:05 PM
Subject: Dual Air Conditioning in a Vanagon
> Marshal Ruskin asked:
> > Please tell me more about the second evaporator you installed,
>
> OK, here are the basics of the two air conditioning system for the
> Vanagon.
>
> I used an evaporator from Cooler Air Products ((972)-771-3791, Rockwall,
> Texas). This is essentially a Behr after market unit that mounts behind
> the dash above the glove box. It uses the original fresh air vents on
> the sides of the dash as well as two new vent coming out of the old ash
> tray opening. The refrigerant lines were plumbed in parallel. I
> modified the controls from what Cooler Air suggested. The thermostat
> for the front unit controls the compressor magnetic clutch and the rear
> unit thermostat controls a solenoid valve in the refrigerant line to the
> rear (original) unit. There is an over pressure switch to protect the
> system from excessive refrigerant heat/pressure. Both evaporators have
> R134a expansion valves. The system was converted to R134a (~50 oz) and
> the compressor is a Sanden SD709. I am using the original VW
> condenser. The controls are mounted on the dash to the left of the
> steering column and are essentially a double set of the standard VW
> Westy AC thermostat/fan switch unit. To run the thing you simply turn
> on the front air conditioning and set the fan speed and temperature. If
> you want the rear unit on you turn on the rear fan switch and adjust the
> rear thermostat for the temperature in the rear. There are two LED's
> (green) to indicate when the thermostats are calling for cooling so I
> can make small adjustments in the temperature when my family screams
> "It's too cold back here!", and a third LED (red) to indicate when the
> overpressure switch shuts off the compressor. Generally I run both fans
> on low and cooling is adequate except when the outside temperature is
> above 100 deg F or we are stopped in traffic. The system has been
> reasonably problem free but I would like to have more condenser capacity
> so the refrigerant pressures would be lower and cooling would be better
> in while stopped and in slow city driving. When driving I usually get
> temperatures of 40 degrees F and 48 degrees F with one and both
> evaporators running, respectively. The 40 degrees is limited by the
> thermostat and not the cooling capacity. When both systems have their
> fans running on high there is a tremendous amount of air moving in the
> bus. Temperatures are higher without a generous flow of air through the
> condenser. I've been thinking of adding an additional, fan cooled
> condenser under the floor or above the axles. This would be plumbed in
> series with the original condenser.
>
> The system works well. The nicest thing about it is that it provides
> great cooling in the front footwells.
>
> Any other questions?
---
Outgoing mail is certified Virus Free.
Checked by AVG anti-virus system (http://www.grisoft.com).
Version: 6.0.372 / Virus Database: 207 - Release Date: 6/25/2002
|