Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (September 2002, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 18 Sep 2002 06:22:21 EDT
Reply-To:     RAlanen@AOL.COM
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Frank Condelli <RAlanen@AOL.COM>
Subject:      Re: power door locks prob
Comments: cc: VW87JETAGL@aol.com
Content-Type: text/plain; charset="ISO-8859-1"

In a message dated 9/18/2002 12:01:07 AM Eastern Daylight Time, LISTSERV@GERRY.VANAGON.COM writes:

> anyone ever have when the driver door is unlocked the passenger lock will > not > go up at all and then the drivers automatically relocks itself. when i use > the passenger to lock or unlock everything works great > any ideas > Patrick, this is a VERY common problem but there are numerous reasons why it is occurring. You must methodically disassemble each of the front door power door lock mechanisms and check all the contacts and wiring from door to door. I have found that sometimes it's the contacts inside the mechanism that are corroded, or the sliding plate springs have seized, or one of the junctions has corroded contacts, or a wire has broken in the door harness between the door and door post usually where the bending occurs when opening and closing the door. When you get the mechanism open you can do the following test: Red wire 12 v + power always. Yellow and white are the activation wires for opening and closing the opposite door and vice versa. Make a jumper wire from a short piece of 14 gauge wire and jump 12v + from the red to the white and then the yellow. The opposite door mechanism should open and close. If not then there is a broken wire some where in whichever wire does not activate. Once you jump and activate one of the wires it then becomes 12 v + if the other door switch is working properly. What you have here is a common three way switch. Use dielectric grease on all electrical contacts and connections after cleaning off any corrosion. Use light machine oil to lubricate the motor bushings. Use white lithium grease on the gears. Hope this has been helpful and good luck. Cheers  

Frank Condelli Almonte, Ontario, Canada <A HREF="http://members.aol.com/BusFusion/bfhome.htm">BusFusion</A> a VW Camper camping event, Almonte, ON, June 12 ~ 15, 2003 '87 Westy & Lionel Trains Member: <A HREF="http://www.vanagon.com/">Vanagon List</A>, <A HREF="http://www.bcn.net/~limbo/">LiMBO</A>, <A HREF="http://www.westfalia.qc.ca/">IWCCC</A> & Capital City VW Club Vanagon/Vanagon Westfalia Service in the Ottawa Valley <A HREF="http://members.aol.com/Fkc43/stebro.htm">STEBRO/Vanagon Stainless Steel Mufflers</A>   <A HREF="http://members.aol.com/Fkc43/busindex.html">Frank Condelli & Associates</A> or http://frankcondelli.com


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.