Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (November 2002, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 28 Nov 2002 18:28:28 -0800
Reply-To:     Ward Smith <wsmith@SAN.RR.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Ward Smith <wsmith@SAN.RR.COM>
Subject:      Re: how to HOT-WIRE a Vanagon?
Comments: To: mark drillock <drillock@EARTHLINK.NET>
In-Reply-To:  <3DE6BE29.3C683518@earthlink.net>
Content-Type: text/plain; charset="iso-8859-1"

Run a "hot" jumper wire to the + side of the coil and then "arc" the starter. To do this, pull the single clip-on wire connector on the starter and attach your own clip w/wire. Then jump this wire to battery power. The closest one is right next to you on the starter.

Should turn the engine over and fire it up.

I have used this system to trouble shoot engine problems when you are by yourself (never for evil purposes) but I'm not positive the jumper wire to the coil will power all the systems (like the fuel pump, etc.). I usually have the key for this procedure, so I'm not 100% sure. I know it works on the earlier air-cooled VW's-whch I have much more experience with. If this doesn't work, you can also "manually" power up the fuel pump by pulling a relay in the engine compartment and running power to it. If you need to know how to do this, let me know.

GL,

Ward

-----Original Message----- From: Vanagon Mailing List [mailto:vanagon@GERRY.VANAGON.COM]On Behalf Of mark drillock Sent: Thursday, November 28, 2002 5:09 PM To: vanagon@GERRY.VANAGON.COM Subject: Re: how to HOT-WIRE a Vanagon?

The simple answer is to buy an ignition switch. They are about $15. Remove the 2 screws that hold the lower cover over the steering column. Unplug the wiring connector from the installed ignition switch and plug it into the new one. Use a screwdriver to turn the new one. The steering will still be locked but everything else will work normally.

"J. Harvey" wrote: > > I'm looking into buying a rolled/crused Vanagon for parts but it has no keys > and I can't get the tumbler code. I'd like to be able to test the engine > etc. with out having to buy an ignition switch w/key. So, my question is > how do I hot-wire a Vanagon? Please p-mail me....I don't want to cause any > trouble. Or post your ceative solution publicly. Thanks in advance, John > > _________________________________________________________________ > Tired of spam? Get advanced junk mail protection with MSN 8. > http://join.msn.com/?page=features/junkmail


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.