Date: Mon, 2 Dec 2002 12:52:03 -0500
Reply-To: Kenneth Wilford <kenwilfy@COMCAST.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Kenneth Wilford <kenwilfy@COMCAST.NET>
Subject: FW: My first set of heads ?
Content-type: text/plain; charset=iso-8859-1
My opinion:
If you are going to do this then using a set of used heads is a gamble. It
is less of a gamble if you are taking them to a local machine shop, and
having them pressure tested and also checked for straightness. If there is
any pitting it should be filled with JB weld and the head sanded down.
However most of the time the cracks between the valves are large. You wind
up with a head that either has a crack that is so big that you already have
a leak (coolant into combustion chamber) or soon will. Also with the cracks
between the valves there is the possibility of dropping a valve seat.
Occasionally you can find a set of good used heads with no cracks between
the valves (rare). These would probably be the only set I would use. Get
them pressure tested and while they are at it, have a valve job done.
New heads or low mileage heads are the only way I like to go. I sell new
AMC heads with valves and springs already installed and ready to go for
$395. This is the fastest, and best way to go if you have the money. These
are great heads, they bought the molds from VW so the castings are OE and
they have even updated the alloy to make them more resistant to corrosion.
I have not had a single problem using these heads. I have installed them
myself on my own van and drove it for a few years. No problems!
List member discount of 5% would apply to these.
Also before you put the new gaskets on I would check the case for pitting.
Any pitting you see should be filled with JB weld and then sanded smooth. I
have only had one head gasket job I have done ever leak and it was because
of a severely pitted case. I learned that lesson the hard way, so now I
always fill the pits in the case, and I have had no more problems.
We have German engine gasket kits that include the black and yellow sealant
and all of the o-rings and gaskets you will need to do your head change for
$120. Hope this helps.
Thanks,
Ken Wilford
John 3:16
http://www.vanagain.com
Phone: (856)-327-4936
Fax: (856)-327-2242
-----Original Message-----
From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com]On Behalf
Of Herb Mooney
Sent: Sunday, December 01, 2002 6:22 PM
To: vanagon@GERRY.VANAGON.COM
Subject: My first set of heads ?
Well... replaced the exhaust, clutch, and alternator so far in my 91
Vanagon. Now I noticed the drivers side head gasket is dripping antifreeze.
I guess it's time to do the gasket. I'm new to this problem so what should I
expect to pay for a set of complete heads in case mine need to be machined?
I figure I should buy a set to swap in for a quicker repair, but will have
the old set machined for back ups. I'm assuming I shouldn't drive the
Vanagon till it's been fixed or can I get away with a little driving till I
find new heads? It's dripping very slowly and not overheating. No fluid in
the oil so far. I noticed some used ones on ebay, is this asking for
trouble? Thanks for the advice,
BTW - anyone have a set of heads I can buy for my 2.1?
Herb in PA
----- Original Message -----
From: "Ben T" <BenTbtstr8@AOL.COM>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Sunday, December 01, 2002 5:43 PM
Subject: Re: cool panelvan on ebay.de
> In a message dated 12/1/02 9:18:50 AM Pacific Standard Time,
JordanVw@AOL.COM
> writes:
>
> << they were only sold in Canada, so youd have to find one up there
(rust!!)
> and
> import it over the border. you'd need a letter of compliance and other
> changes for customs. >>
>
> As usual, Chris, we have one here in the hotbed of Vanagon activity. My
> friend just bought it last month for $4200. Has an inlne-4 conversion,
power
> mirrors, Porsche 928 phone dial wheels. Front seats from a Carat. Was a
> diesel.
>
> BenT
>