Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (January 2003, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Mon, 6 Jan 2003 01:20:30 -0600
Reply-To:     Stan Wilder <wilden1@JUNO.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Stan Wilder <wilden1@JUNO.COM>
Subject:      Great Engine test stand event.
Comments: cc: vintagebus@type2.com, wetwesties@yahoogroups.com
Content-Type: text/plain; charset=us-ascii

Poppy and myself got organized about a week ago and secured some steel to build the framework for my engine test stand. We faired pretty good and got some bolt together basic frame units that just needed some trimming to make a viable project. (bunches of 5/16" holes had to be drilled) I scrounged around my over filled junk box and came up with a Fiat AEG fuel pump to work with the little weber Carb that I retrofitted to a FI air plenum from a 74-91 FI Vanagon. After a few trips to the hardware store buying generic fasteners (1/3 the cost of metric) and bolting the frames together using stock VW engine mounts and various VW hardware, I wound up with an engine and transmission bolted into a frame. Things being simple on the outside often become complex when its time to make them work. I built a control station for the engine stand that consist of an old tackle box with the additions of a tachometer, oil temp, oil pressure, cylinder head temp, volts gage. Included in the control station are a main power switch, fuel pump switch, starter bottom and a vacuum gauge. I didn't run out of room I just ran out of necessities. The whole birds nest was basically from stock parts on hand and no major cash outlay was necessary. Since the engine test stand has been built as a KD apparatus I calculated that permanent controls would be more wasted than wanted. One regret was that I had to install a full transmission because I didn't have a surplus bell housing so the total package is 48x48" in length and width give or take a few quarters. I'm working on getting some pictures posted. One thing I discovered early on, I had an oil pump on the first engine that just would not prime. Switching it out was a fairly quick process and I immediately got pressure from on the replacement pump with over 5 bar pressure (75 psi) just turning the engine over with the start and 10/30wt engine oil. I'm still a few hours from starting the engine because I left a check valve ball out of the Fiat fuel pump (don't know if it is required) and I think I should put it back in just to be safe. I'm just guessing but I'm going to say that I've probably saved one engine already by my strange and extreme detail procedures.

Stan Wilder 83 Air Cooled Westy

________________________________________________________________ Sign Up for Juno Platinum Internet Access Today Only $9.95 per month! Visit www.juno.com


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.