Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (January 2003, week 5)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 29 Jan 2003 09:43:59 -0500
Reply-To:     David Beierl <dbeierl@ATTGLOBAL.NET>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         David Beierl <dbeierl@ATTGLOBAL.NET>
Subject:      Re: NVC:  measuring impedance of a speaker?
Comments: To: vw4x4@FYI.NET
In-Reply-To:  <3E37C5EE.FA9F5605@fyi.net>
Content-Type: text/plain; charset="us-ascii"; format=flowed

At 07:15 AM 1/29/2003, Eric Zeno wrote: >The impedance between 4 and 8 ohm to an audio amp, >is almost insignificant. Unlike if you where feeding this in >to a 1000 ohm load. Wiring 2 speaker on the same amp >has the same effect as a difference between 4 and 8 ohm >impedance. So, don't be concerned unless your trying >something fancy. > Eric

These are power circuits, and we're talking about a 2:1 ratio of impedance, so it's not entirely trivial. If you're not running at high outputs it no doubt doesn't matter -- but if the source and load impedances are not equal some of the power will get reflected back into the source, which undoubtedly will cause a certain (small) amount of distortion depending somewhat on the length of your speaker wires. Also, if the load impedance is lower than the amplifier is rated to handle (and the ratings vary and so do the safety margins) the output stage of the amplifier can overheat. In a transistor amp the output will overheat (and in case of an actual short circuit may instantly suicide*) when the load impedance is too low. In a tube amp the output transformers will overheat if load impedance is too high (not sure what happens if it's too low, maybe nothing).

Some amplifiers but the speakers in parallel when you run two sets -- reduces (eliminates?) some possible distortion from interaction between the speakers, but means that the load impedance is less -- two ohms for two four-ohm speakers, 2 2/3 ohms for a four and an eight, four ohms for a pair of eights. Others put them in series, which means no overload problem but possible distortion. It's easy to tell, just hit the B speaker button with no speakers connected -- if the A speakers keep playing they're in parallel, if they go silent they're in series.

*The ability of transistors to supply almost infinite current into a short circuit leads to the following rueful ditty: "Transistors fused against the worst, protect the fuse by blowing first!"

david

-- David Beierl - Providence RI USA -- http://pws.prserv.net/synergy/Vanagon/ '84 Westy "Dutiful Passage" '85 GL "Poor Relation"


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.