Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (April 2003, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 23 Apr 2003 09:53:32 -0700
Reply-To:     laurasdog@WEIRDSTUFFWEMAKE.COM
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Steve Delanty <laurasdog@WEIRDSTUFFWEMAKE.COM>
Subject:      Front end misery... but done.
Content-Type: text/plain; charset="us-ascii"; format=flowed

I hate suspension work. I've always hated it, and it's always hated me.

I managed to replace upper and lower ball joints, upper control arm bushings, brake rotors and bearings and new shocks on the westy.

I was going to do the lower control arm bushings also, but after pushing and prying on them a bit I decided they were still O.K. for awhile. Besides, I was pretty much out of steam by the time I got that far... oh well.

Saturday (and most of friday) was a lesson both in why I hate to do it myself, and in why I never trust anyone else to do it for me...

The brake rotors were severely worn. They wore flat and even, but the entire area where the pads make contact was worn down almost 0.1" on each side! The last shop to work on It put a brand new set of pads on trash rotors. Idiots...

I knew I was in trouble to start with when I went to dig my crummy old hydraulic press out and assemble it and some of the critical parts were missing. The jack and the frame were there all right, but some of the assorted plates and attachments seem to have wandered off in the 6-7 years since I last used it. Rats...

I started on the left side and had no trouble getting the brakes off other than not having enough room to fit my breaker bar and extendo-pipe to bust the big brake caliper bolts. I highly recommend that folks doing front brakes get the "hardware kit" that has the little rubber boots for the slider pins and some silicone grease. The boots on mine were toast, and the pins on the drivers side were really rusty and jammed up. They were long overdue for removal, cleaning and greasing...

The upper ball joint was a bitch. The 8mm allen caps that hold the joint to the control arm were way stubborn and I spent close to an hour getting those suckers out. Repeated encouragement from a propane torch, lots of penetrating oil, and an 8mm allen on a 1/2" drive breaker bar finally did the trick. For a while I figured I was going to end up ripping the centers out of the bolts but they finally let go with a loud snap. The first one surprised me and sent me over backwards when it let loose...

The upper control arm came off easy. The first thing I noticed was that the last person to change the upper bushings hadn't bothered to spot weld the new ones back in. Idiots... The bushings pressed out easily, and the new ones went in easy. I spot welded them in like they're supposed to be.

The lower ball joint was a no go for my little press. I ended up taking it for a drive to where I could use a real press on it. Those suckers are in TIGHT.

The drivers side went back together fairly smoothly. -----

The passenger side... The first thing I noticed is that the nut holding the wheel bearing on had not been peened in place to prevent it from loosening. Maybe that's why the bearing on that side was so loose. Idiots...

I got the upper ball joint out with less trouble than the other side because I soaked the bolts with oil the night before and started by heating them a bit with the torch before I tried to loosen them. Ahhhh... much better.

I got the upper control arm off and figured the bushings would be fairly easy to replace like the other side. WRONG! Whoever did the drivers side forgot to weld the bushings in place, but the passenger side more than made up for it. Whoever did this side was probably a welder at some shipyard in the 40's. These were welded in with welds that were designed to last. A full inch of weld around the bushing, burned in hot and deep.. Idiots... I ground as much of the welds off as I dared, but I had to grind quite a bit of metal from the control arm. Finally I had removed as much as I felt comfortable with and they still were welded in solid, so I ended up cutting the fat end off the bushing, driving all the guts out, then using a hack saw inside the bushing shell to cut it and peel it out with pliers. Then I used the die grinder to remove the last weld bits from inside the control arm. It took over 2 hours to get the 2 bushings out of the control arm.... Aaargh.

Anyway, the rest of it went back together O.K. It took most of 2 days to get both sides done.

Front end work is a nasty dirty job and I hate every second of it, but it's always such a joy to have it done. It feels a lot better on the road now. Friday I'll try and get it in for a front end alignment.

I hope my knuckle feels better soon. I smacked the hell out of it with the BFH and it still hurts after 5 days... Did I mention how much I hate front end work? Oh well... it's good to have it done.

Happy motoring, Steve


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.