Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (August 2003, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Mon, 4 Aug 2003 16:27:34 -0700
Reply-To:     Damon Campbell <damoncampbellvw@YAHOO.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Damon Campbell <damoncampbellvw@YAHOO.COM>
Subject:      Re: digijet EFI on digifant engine - throttle switch in
              particular - the answer
Comments: To: JM/CO <jmerritt2@capecod.net>
In-Reply-To:  <001d01c35ad5$273192c0$651b4b43@net>
Content-Type: text/plain; charset=us-ascii

Thanks Chuck,

You've hit the nail on the head with this one... i was just at a local bus specialist (BusLab, in berkeley, CA), and they just happened to have a 2.1 in a 1.9 sitting there, and lo, what did they show? Exactly what you describe. Fortunately, i have the complete 2.1 wiring harness, so i'll just be snipping off that connector and grafting it onto my 1.9 harness. The 2.1 switch setup is simply a part reduction of the earlier system - electrical function remains the same.

Gracias for the informative response, -Damon

--- JM/CO <jmerritt2@capecod.net> wrote: > The use of the single switch did not occur as a > result of the change to > Digifant, but was a modification of the Digijet > system in ( I think ) 1985 > 1.9L models. You must have the correct wiring > harness to use this, > otherwise, use the original. > Chuck > '83 Westy > ----- Original Message ----- > From: "Damon Campbell" <damoncampbellvw@YAHOO.COM> > To: <vanagon@GERRY.VANAGON.COM> > Sent: Monday, August 04, 2003 2:05 PM > Subject: digijet EFI on digifant engine - throttle > switch in particular > > > > Hello list, > > > > I'm getting closer with the details of my wbx > build, > > with only some minor snags looming in the horizon. > I > > am planning on using the 2.1 intake > > manifold/runners/throttle body as they are > slightly > > larger to handle the increased displacement. > However, > > the idle/WOT switch is very different in the > > digifant/jet systems. Namely, only one switch for > > both on dijifant, and they each get their own in > > digijet. Should i just bypass the WOT switch, and > set > > it up to only activate the idle switch? Or is > there a > > more clever way of maintaining the two-switch > > functionality? > > > > Thanks, > > -Damon > > > > ===== > > '84 Westy (Sparky) > > '65 Kharma Ghia (Dharma) > > > > __________________________________ > > Do you Yahoo!? > > Yahoo! SiteBuilder - Free, easy-to-use web site > design software > > http://sitebuilder.yahoo.com >

===== '84 Westy (Sparky) '65 Kharma Ghia (Dharma)

__________________________________ Do you Yahoo!? Yahoo! SiteBuilder - Free, easy-to-use web site design software http://sitebuilder.yahoo.com


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.