Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (August 2003, week 5)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Fri, 29 Aug 2003 19:34:58 -0400
Reply-To:     Germain Gagnon <reglys@SYMPATICO.CA>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Germain Gagnon <reglys@SYMPATICO.CA>
Subject:      Re: Fixed Propane Fridge
Comments: To: Malcolm Stebbins <mwstebbins@YAHOO.COM>
Content-Type: text/plain; charset="iso-8859-1"

I agree 100% with Malcom. The cleaning of the combustion chamber makes a big difference in the lighting of the fridge.

BTW Malcom, very good pictures.

Germain

----- Original Message ----- From: "Malcolm Stebbins" <mwstebbins@YAHOO.COM> To: <vanagon@GERRY.VANAGON.COM> Sent: Friday, August 29, 2003 9:31 AM Subject: Re: Fixed Propane Fridge

> I will respond to SEVERAL posts (Frank, Kim, Shawn), > in this ONE email. And I will refer to my photos at: > http://photos.yahoo.com/mwstebbins Just m2cw. > > --- Frank Condelli <RAlanen@AOL.COM> wrote: > > > Shawn, you need to use air from an air compressor > to blow air > > into the drain at the bottom of the fridge. 100 ~ > 120 lbs. This will clear out > > the combustion chamber and tubes... > > Frank: I'm not as optimistic about this as you are. > If one looks at my photos one can see all of the CRUD > in the combustion chamber. If one just blows air in > there, one may disturb the crud. Now that disturbance > MAY cure the problem temporarily, but it MAY make > things worse as the crud may land in/on the burner > grill or the air hole or piezo lighter stem. IMHO one > should clean out the chamber and the jet and clean off > the piezo lighter probe and the heat sensor. This is > a DIY project. If I can do it, anyone can do it. > > =============================== > > --- Kim Brennan <kimbrennan@MAC.COM> wrote: > > I push in the propane button, (light starts > > flickering). I turn on the > > thermostat. I turn on the propane supply, I push in > > the little button. > > Voila blue flame in the sight glass. > > > > I release the little button. Blue flame goes out. > > Yah, that sure seems > > to be a pressure regulator issue. Drat > > Kim: Just be to sure, do you hold the "little button" > in for 10 seconds after the flame lights??? The heat > sensor (in the combustion chamber) needs a few seconds > to heat up to send the signal to the control unit > (Auto shut-off valve) to let it know that the flame in > on. Also, if the flame lights with the (by-pass) > button pushed in, why do you suspect the pressure > regulator? Why not suspect the by-pass switch?? > > ================================ > > --- Shawn Wright <swright@ZUIKO.SLS.BC.CA> wrote: > > > can hear the gas flowing when > > bypass button is pressed (with > > > hose to ear), so I know gas is there. I'm starting > > suspect the piezo is not > > > firing every time, or the spark is very weak, so > > it is flooded with gas, then a > > > large pop ignites a whole lot of gas an blows the > > flame out (or runs out of O2). > > > Any quick tips to getting it going tonight w/o > > pulling the fridge? Otherwise I > > > guess I'll be buying ice :-( > > Shawn: On my fridge, I can hear a definite CLICK, > CLICK, CLICK for the piezo lighter. Also, just > "hearing" gas does not mean that the combustion grill, > or air holes, are not partially blocked When I took > my combustion chamber apart, the heat sensor had some > crud on the end that MAY have interfered with the > sensing. I would not jump to conclusions till after > the assembly is taken apart and cleaned. > > =========================================== > > > I've had the flame start (and LED light) sometimes a > > few seconds after spark, but > > never this long after (maybe 10-20 seconds). I'm > > leaving it on overnight and hoping it > > will last the weekend... :-) > > I'm not sure about this, but... If, on your model, > the LED is tied into the heat sensor, that would > explain why it takes a few seconds to come on after > the propane lights. Also FWIW if I turn the propane > switch AND the DC switch "on" at the same time, the > fuse melts. > > > m2cw & I'm not an expert. Malcolm > > > __________________________________ > Do you Yahoo!? > Yahoo! SiteBuilder - Free, easy-to-use web site design software > http://sitebuilder.yahoo.com


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.