Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (September 2003, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 3 Sep 2003 08:49:07 +0100
Reply-To:     Tony Polson <tp@WHSMITHNET.CO.UK>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Tony Polson <tp@WHSMITHNET.CO.UK>
Subject:      Re: Hard starting 84 vanagon - stumped
Comments: To: Brian Keese <bkeese@DIRECWAY.COM>
Content-Type: text/plain; charset="iso-8859-1"

Brian Keese wrote: > > Hi List, > > Well, I've joined the list again after a two-year hiatus - last time I was on the list it was mostly for fun. This time it is unfortunately by necessity. > I wonder if anyone can offer any advice to my mechanic in fixing my 84 Vanagon, 'The Ark'. He doesn't have e-mail. > > Here's my description of the behavior: > I turn the key to start the van. > The van cranks and cranks and eventually starts. > Sometimes it needs to crank for up to a minute, then it starts and runs just fine. > I don't know if it is related, but the van has always (in the 4 years I've owned it) run a little rough after warming up half way - sometimes stalling. When cold and fully warmed up it runs fine. > I never worried much about this because it would always just start right back up and I could keep on trucking. Now when it stalls, I can't get it to start back up and I'm afraid of causing an accident. That's why I brought it in to be checked out. > > I brought it to a mechanic who I trust and he went through all the normal testing procedures. Everything checked out OK, so he had me send the ECU in to be checked out. I sent it to Darrell Boehler and he checked it out on the bench for a few hours. Everything checked out OK. He sent me a road-tested ECU from an 85. My mechanic put it in and the van still exhibits the same behavior. He doesn't know what else to do. > > Here's what he said: > When the van doesn't want to start, the injectors are getting no ground signal from the ecu. > He checked and replaced all the grounds as necessary. > He went through the testing procedures for each of the injection system sensors - all test OK, even the TEMP2 sensor. (He did comment that the problem doesn't seem to be temperature related.) At first he thought the hal sensor was bad, but then further testing proved it to be OK. > Of course, he also checked the fuel pressure and spark and they checked out OK. > > Any hints or ideas would be greatly appreciated. > > Brian Keese > > BTW: I read on the list about a weak starter causing somewhat similar behavior. I know my starter needs a rebuild (sometimes I have to bang on it to get it to turn over). Maybe it's just that the starter is bad and his testing methods are off a bit. I doubt it, but I thought I'd just throw that out there.

Hi Brian,

I had a similar problem after leaving my van standing for several months - I had a small electrical fire behind the dash and it took me some time to get around to fixing it. By the time I did I had a "lazy starter" and the engine simply would not fire. I even changed the battery for a new one ... still wouldn't fire.

Your last paragraph (BTW ...), especially your suggestion that your starter is "slow", and the fact that your mechanic suspected a ground problem suggests that you may have the same problem ... on my van, the ground strap between the engine/gearbox and body was not making a full electrical connection at one or both ends. This resulted in the starter motor hogging all the battery power and only reduced voltage being available at the engine management system - that reduced voltage being insufficient to fire the ignition.

Merely replacing the strap is not enough; you need to clean the surfaces with which the ground strap makes electrical contact. You need to do it thoroughly. The body connection will suffer from rust and electrolytic corrosion. The rust should be sanded back to bare metal before fitting the new ground strap, and the whole area should be coated with underbody seal to delay any future problems in that area.

The earth strap connection to the engine crankcase will suffer from aluminum corrosion, and the white oxide of aluminum is a very effective insulator. Once again, sand to bright metal and coat the finished connection with some protective coating so as to delay any recurrence of the problem.

I intend to fit at least one additional ground strap in the hope that my van won't suffer from this problem again for some years. I know that I will have a lot of other problems to contend with in that time, so avoiding any repeat performances from the ground straps seems like A Good Idea ...

I hope this works for you.

Best regards,

Tony


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.