Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (October 2003, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 23 Oct 2003 15:51:24 -0400
Reply-To:     Marla Stelk <mjstelk@HOTMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Marla Stelk <mjstelk@HOTMAIL.COM>
Subject:      Re: sheer bolts/steering column - another question
Content-Type: text/plain; format=flowed

Okay - so I just replaced my front heater core, and it removing the whole
dash, the bolts holding my steering rack on to the underside of the dash
that everyone warned me about were slotted.  They had that cone head, but it
was slotted so I just used a normal flathead and had no problems removing
them or putting them back.  Am I in any danger because I didn't use locktite
or some sheer bolts (whatever they are..)?


Peace,
Marla
'87 Westy GL "Vana Morrison"




>From: gary hradek <hradek@YAHOO.COM>
>Reply-To: gary hradek <hradek@YAHOO.COM>
>To: vanagon@GERRY.VANAGON.COM
>Subject: sheer bolts/steering column
>Date: Tue, 21 Oct 2003 12:32:24 -0700
>
>Jeff,
>      It is not so the torque is right but so the bolts
>sheer during an accident.   I would reuse them and
>perhaps use some locktite.   gary
>Date:    Tue, 21 Oct 2003 02:47:50 EDT
>From:    Jeff Oxroad <Oxroad@AOL.COM>
>Subject: sheer bolts/steering column
>
>What is the function of a sheer bolt as in the two
>that mount the
>steering
>column tube to the bottom side of the dash board.
>
>Bentley says once sheer bolts are removed (drilled
>out) they must be
>replaced
>with new sheer bolts. These new bolts are to be
>tightened until the
>head
>sheers off. Is this to exact the perfect torque or
>make them difficult
>to remove?
>Or are they "sheer bolts" because they are designed to
>sheer off in the
>unlikely event of a collision?
>
>FWIW I was able to remove the sheer bolts with vice
>grips and no
>drilling.
>Now, must I replace the sheer bolts with new sheer
>bolts or can I reuse
>the used
>sheer bolts--installing them with vice grips or will
>regular hex head
>bolts
>suffice?
>
>Jeff
>83.5 Westy
>LA,CA
>
>
>__________________________________
>Do you Yahoo!?
>The New Yahoo! Shopping - with improved product search
>http://shopping.yahoo.com


_________________________________________________________________
Never get a busy signal because you are always connected  with high-speed
Internet access. Click here to comparison-shop providers.
https://broadband.msn.com
Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!

Return to the archives @ gerry.vanagon.com

The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.