Ben, Sounds like you have a good idea what's going on here. My advice would be to switch to synthetic, Mobil 1 15W50 is supposed to be "the best". As far as I've been able to determine, low oil pressure is caused by a low "resistance" to oil flow between the oil pump and the sensor or just a bad oil pump. Probably your bearings have worn to the point that they don't provide the expected resistance to oil flow that was planned during the design phase of the motor. As others have noted, as the oil heats up, the viscosity drops resulting in lower pressure, 1/2 "full" is supposed to help reduce the oil temps vs "full". You can probably run this engine for the few months until the snow melts by just keeping the rpm's at a comfortable range (3-3.5K, maybe 4.0K for a SHORT time) and taking it easy on the hills. My advice would be to keep the oil level at 1/2 way between the marks and just take it easy on those hills. You'll have to just peg it at 3500 rpm in 3rd (or 2nd) gear and hold it there even though it would go faster with more throttle. Take your time - the alternative is a rod through the case, BTDT and that's no fun.... -jeff
Dennis Haynes wrote: > Is the light coming on or are you getting the light and buzzer? If only > the light, than you may have a bad switch or a wire shorting to ground. > 120K is not reason for a rebuild on its own. With care and luck, the > lower end can double that. You need to do some troubleshooting. Both > electrical and mechanical with oil pressure gauges. When replacing the > switches, make sure to get the correct ones. The high pressure switch > (rear) should be .9 bar, not the 1.8 many parts books indicate. Also, > make sure the oil level is not too high. The top dipstick mark is "Max", > not "Full" Oil level mid way works best. > > Dennis > > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf > Of Ben S > Sent: Friday, January 09, 2004 12:26 AM > To: vanagon@GERRY.VANAGON.COM > Subject: Re: what causes low oil pressure > > well thanks for the advice everyone. i do indeed have a 2.1 wbx, and it > rolled over 120k miles just before the oil light last came on. i know > that it is about time to rebuild or replace this engine, but i'm hoping > to wait until snowboarding season is over to do it since this is my only > car and i can't very well ride my motorcycle to the mountain! > > the scenario posed in boston bob's article seems like a probable > explanation: some bearing is wearing down, a clearance is increasing, > and too much oil is escaping. the only thing i don't understand is why > this would be exacerbated by heavy engine load or high engine speed. it > seems to me that the oil pump is spinning faster at high engine speed >and could more easily maintain output pressure at a high flow rate. > > i have heard people mention a high oil pressure sensor... does that also > set off the light and buzzer? could i actually be having excessive > pressure? > > i guess in the end i just need an oil pressure gauge. is it possible to > install a sender for one in place of switch that drives the light? i > have also been thinking of switching to a full synthetic oil, but i'm > afraid that my oil leakage/consumption will worsen. > > Ben. > |
Please note - During the past 17 years of operation, several gigabytes of
Vanagon mail messages have been archived. Searching the entire collection
will take up to five minutes to complete. Please be patient!
Return to the archives @ gerry.vanagon.com
The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.
Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.