Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (March 2004, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Mon, 15 Mar 2004 14:35:32 -0500
Reply-To:     David Beierl <dbeierl@ATTGLOBAL.NET>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         David Beierl <dbeierl@ATTGLOBAL.NET>
Subject:      Re: [subaruvanagon] 1987 VW Tach - Special Request
Comments: To: subaruvanagon@yahoogroups.com
In-Reply-To:  <c3497k+j3to@eGroups.com>
Content-Type: text/plain; charset="us-ascii"; format=flowed

At 07:57 AM 3/15/2004, fastvanagon wrote: >If possible, I need these measurements done with a digital meter. >With the "T14" connector unplugged, start the Vanagon and do a >voltage measurement across pin number 3 and pin number 9. Again, do >the same for the current measurement. Verify that the meter is set >to the proper 12VDC setting for the voltage. Verify that the meter >is set to the proper DC current measurement. If you are unsure of >these meter settings or pin locations, please do not attempt.

Erm...I'd suggest not doing this, and in particular not doing the current measurement. In the '87 and all other watercooled Vanagons, the tach drive is connected directly to the ignition coil drive signal. If you don't believe me you can do a continuity check between the panel connector and the dual terminal on the ignition coil -- or just lick your finger and put it on the connector on the back of the tach while the engine is running. Try not to be driving when you do this, it upsets the other drivers. Or of course you could look at the wiring diagram...

Voltage measurements will only be accurate if you use an oscilloscope (I suspect something like 200 volts peak, and if you really need it I can measure it on my '84). This is not enough to pop the input stage of your average meter, but it's a consideration you should bear in mind. The meter *will* give you the average voltage with a fudge factor to read as RMS or "effective" voltage -- but the fudge factor assumes a sine wave and not a pulse train, so unless you're using a meter with true RMS readings it won't be accurate. Someone on this list (Mark Drillock?) knows whether the tach counts pulses or simply integrates the input signal the way a digital meter does -- I suspect the former.

Measuring current from this signal to ground is equivalent to shorting the coil drive to ground through the shunt resistance of the meter. Shorting the output stage of transistor devices is seldom a good idea because the transistor can destroy itself in the blink of an eye from overcurrent. "Transistors fused against the worst -- protect the fuse by blowing first..." In the case of the 2.1l Digifant, that transistor is located inside the ECU.

david

-- David Beierl - Providence RI USA -- http://pws.prserv.net/synergy/Vanagon/ '84 Westy "Dutiful Passage" '85 GL "Poor Relation"


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.