Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (September 2004, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Thu, 2 Sep 2004 11:26:19 -0400
Reply-To:   Tom Corbitt <corbitt@ANR.MCNC.ORG>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   Tom Corbitt <corbitt@ANR.MCNC.ORG>
Subject:   Re: gauge mod help
Comments:   To: Mark Cumnock <kayakwesty@YAHOO.COM>
In-Reply-To:   <vanagon%2004090108500716@GERRY.VANAGON.COM>
Content-Type:   text/plain; charset=us-ascii; format=flowed

Mark Cumnock wrote:

>I have an aftermarket gauge, that i am wanting to make read 1/3 lower . I >got a water temp gauge, and I am using it as a oil temp gauge. I would >like for it to read a little lower, the upper end of the gauge the number >are low, so the gauge almost pegs out. > >Do you install a resistor in line with sensor, what size resistor would it >take. > >Hope someone has a clue on this ...... > > > >

Do you know the behavior of your sender (does it have a negative or positive temperature coefficient?, what is it's resistance range?) and the characteristics of the meter you're using? I'd bet that it's a negative temp model, meaning the resistance of the temp sensor decreases as it's heated. As the resistance goes down, more current flows in the circuit which moves the meter. In that case it's just a matter of splicing in a variable resistor into the circuit in series with the sender unit. Set the pot to 0 ohms, start the van and wait for it to reach your max temp. The adjust the pot (increase the resistance) so that the needle is at whatever point you want it to be at. You can then either leave the potentiometer in the circuit or disconnect it, read the resistance between the wiper and the leg, and then replace it with a set resistor of the same value. You'll then have to calibrate the dial to it's new range and either mark the face or open the meter up and create a new dial. Most temp sensors I've seen usually go pretty low (in the ohms department) at high heat, you'd probably be fine with a 1k Pot (you could go with a 5k pot, you'll just have a harder time hitting the sweet spot) I'd argue that for the amount of time you're going to spend calibrating the dial for your range you could probably go out and pick up a cheap oil gauge and be done with it, but what do I know?

If your system is positive or has something else going on inside it it's going to be a different path. It's possible to build an circuit to condition the signal from the sender to allow you to "dial in" whatever you want on the display, probably the easiest way would be a transistor inverter circuit or an op amp which could be designed to handle/convert inversely-proportional and non-linear sensor inputs. As with the first paragraph, it's really a question of what value you place on your time.

I'm assuming that you've got a voltmeter and know enough about electronics to understand concepts like voltage/current and which leg of a pot is which.

cheers, tom corbitt


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.