Date: Tue, 14 Sep 2004 19:17:14 -0700
Reply-To: Mike Miller <mwmiller@CWNET.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Mike Miller <mwmiller@CWNET.COM>
Subject: Re: speaking if clutch slave failure
In-Reply-To: <EEEJIEJFIKFOCCBNCFHCGEBCCDAA.wilden1-1@sbcglobal.net>
Content-type: text/plain; charset="ISO-8859-1"
Don't forget the pilot bearing!
Really.
Don't ask.
Mike
On 9/14/04 2:30 PM, "Stan Wilder" <wilden1-1@SBCGLOBAL.NET> wrote:
> You don't want to have to go through this again.
> Have the flywheel machines to a new true surface free of flaws and wear.
> Install a new clutch seal Install a new throw-out bearing.
> Good Luck. John Rodgers 88 GL Driver
> -------------- Clip ---------------------
> That's a good start on the preventive maintenance routine but you should
> include.
> 1) New front main crank seal.
> 2) Install tranny main input drive shaft seal. (Behind the throw-out
> actuator arm).
> 3) Flywheel to crank O Ring.
> 4) New soft steel lock-ring for flywheel bolts.
> 5) Flywheel felt seal at the pilot bearing. (If you can find one) Check the
> plumbing supply section of Ace hardware they have a nice graphite
> replacement washer.
> 6) New pilot bearing.
> 7) New bushing for the starter in the tranny case.
> 8) Clean your starter solenoid and blow out loose copper and dirt from the
> starter while you've got it on the bench.
>
>
> Stan Wilder
> More Power with Performance Coatings
> http://www.engineceramics.com
>
> -----Original Message-----
> From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com]On Behalf Of
> John Rodgers
> Sent: Tuesday, September 14, 2004 3:30 PM
> To: vanagon@GERRY.VANAGON.COM
> Subject: Re: speaking if clutch slave failure
>
> First hand experience with clutch shudder in a manual tranny!! Oil on
> the clutch disc face!! This usually comes from a leaking clutch seal.
> It will simply get worse, and eventually result in clutch slippage. It
> is already probably to late to save the clutch disc.
>
> FIX:
>
> Drop the tranny, re-move and replace the clutch disc.
>
> Inspect the clutch plate thoroughly. It may need to be replaced,
> especially if it shows any signs of overheating. If there is any age
> (miles) on it go ahead and replace it. Now is the time. The fingers and
> springs can lose their temper if they get to hot. You don't want to have
> to go through this again.
>
> Have the flywheel machines to a new true surface free of flaws and wear.
>
> Install a new clutch seal
>
> Install a new throw-out bearing.
>
> Good Luck.
>
> John Rodgers
> 88 GL Driver
>
>
>
> Michael Rule wrote:
>
>> Hi All,
>>
>> What are the signs when driving/shifting of a clutch slave failure? Or
>> perhaps I should ask what it's function is... never had a hydraulic
>> clutch system before. Found lots of fixes in archives but not so much
>> a descript of the failure symptom (save leaks!).
>>
>> I ask as I have a "shuddering" if I am not über-gentle releasing the
>> clutch after shifting into first... thought it might be the broken
>> tranny mount, but that fix has not cured the shudder.
>>
>> Thanks,
>> Mike
>>
>>
>>
>> _______________________________
>> Do you Yahoo!?
>> Declare Yourself - Register online to vote today!
>> http://vote.yahoo.com
>>
>>
>>
> ---
> Incoming mail is certified Virus Free by AVG.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.760 / Virus Database: 509 - Release Date: 9/10/2004
>
> ---
> Outgoing mail is certified Virus Free by AVG.
> Checked by AVG anti-virus system (http://www.grisoft.com).
> Version: 6.0.760 / Virus Database: 509 - Release Date: 9/10/2004
>
>
|