Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (September 2004, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 15 Sep 2004 17:28:00 -0700
Reply-To:     Vince S <gipsyflies@COMCAST.NET>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Vince S <gipsyflies@COMCAST.NET>
Subject:      Re: Disappearing Coolant - Head Leak?
Comments: To: dave <dmenche914@HOTMAIL.COM>
In-Reply-To:  <BAY9-DAV116tdqVvPdL00066af2@hotmail.com>
Content-Type: text/plain; charset="us-ascii"

It is amazing how little useful information about motor oil is out there. I google it and the same "more than you ever want to know motor oil" I read years ago is still most informative article. There are others from oil manufacturers but most have so much marketing fluff that make me very skeptical.

I admit that using 5W30 on Vanagon may be a bit extreme. I probably should have stick with the 10W30 I have use until now.

Just because what is stated in the VW owner's manual doesn't mean it must be accurate and correct. Using very high viscosity oil is old-school thinking. The chart does not distinguish between petroleum and synthetic so I interpreted it have to tailor to the former as it is more prevalent. (I am surprised it mentions synthetic oil can be used)

Many studies have shown that majority of engine wear occur within the first few minutes of starting the engine while very little when the engine is hot. Many of which are attributable to revving the engine before the oil have a chance to form a film between the two wearing surfaces or using oil with too high viscosity.

When I first bought my Miata I was very uncomfortable with the specified low viscosity 5W30 oil (applicable to petroleum base oil as well). Now 12 years later (BTW it is 1992 not 93) the engine is still as tight.

Please refer to the very good viscosity index as well as the flash point of the Mobil 1 vs other oil.

http://www.vtr.org/maintain/oil-overview.html

Mobil does not make synthetic in very high viscosity must be for good reasons. When Mobil 1 was first introduced it was only available in 5W30.

Please note that the SAE viscosity designation method is a very crude notation. You cannot rely on these numbers alone to compare two diversely different quality oil. Many synthetic manufacturers will tell you that with synethic you do not need to change the viscosity for different seasons as you should with petroleum based. Synthetic oil superior resistance to thinning and molecular chain breakdown is the reason you can run significant lower viscosity grade for a given temperature and benefit from the lower frictional loss.

I would like to take some measurement of the oil pressure just to see for myself. Please see the paragraph about the oil pressure with jet boat on Amsoil's website:

http://www.performanceoiltechnology.com/frequentlyaskedquestions.htm

Some Vanagon owners have experienced oil pressure problem with 5W30 but this could be due to 1) worn engine 2) petroleum 5W30 used in hot climate and driven hard 3) faulty pressure sensor.

I recognize Vanagon's flat engine does have some special consideration due to the lifter chatter if poor quality oil filter is used. I have never experience this problem since I switched to synthetic and use only good quality filter. My Vanagon sometimes sits not used for months in the winter.

In closing, I wonder if the oil viscosity chart in the waterboxer owner's manual is inherited from the air cool legacy which operates in a significantly much wider temperature span for a given ambient temperature as well as running much hotter.

- Vince

http://gipsyflies.home.comcast.net 1989 Vanagon GL Camper 1993 Mazda Miata (for sale) 1996 Land Rover Discovery 2005 Mini Cooper S

-----Original Message----- From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of dave Sent: Tuesday, September 14, 2004 5:33 PM To: vanagon@GERRY.VANAGON.COM Subject: Re: Disappearing Coolant - Head Lean?

Read the manual for the Vanagon. Heavy weight oil is recommended. If you put in the thinner stuff (ok for some modern engines) you will drop oil pressure dangerously low, ecspecailly if hot weather, and high load is on engine.

I know from experience that the 5W-30 oil causes oil pressure problems.

i run Mobil 15-50 oil, I would prefer a 20-50, but mobil 1 does not make that (20-50 is recommended multi viscosity for hot (85F plus) weather)_

The problem with oil breaking down does not have to do with thicker oil breaking down sooner, the real problem is that multi viscosity oils tend to break down in viscosity much faster than straight oils.

VW even recommends straight 40 oil for hot weather operation, that is really what I'd like to use, but again, Mobil 1 does not make that product, so i stick with the 15-50.

As stated by other auuthor 5-30 oil is too thin unless you live in a freezing cold area. Also of improtance is stick with a genuine Mann, or Mahle oil filter, Fram filters have greater pressure drop, and do not have a good enough back flow valve. Fram will cause my lifters to clack like crazy after sitting several days, OEM filters solved that problem.

----- Original Message ----- From: "Vince S" <gipsyflies@COMCAST.NET> To: <vanagon@GERRY.VANAGON.COM> Sent: Sunday, September 12, 2004 10:32 AM Subject: Re: Disappearing Coolant - Head Lean?

Chuck,

I agree with you my coolant leak though does not appear to be the sensor and possibly the tank. I was suspectious of the tank as o-ring rarely fail unless you distrub it. I will not be surprised that it is the tank getting britle.

I will carefully unscrew the sensor and see.

I did put in 5W30 yesterday. I had in the past used 10W30 but never anything heavier. My reason is 1) Many high performance vehicles including my supercharged Mini uses 5W30 synthetic so I don't see why the Vanagon couldn't unless the bearing tolerances in it is wider. 2) I read from some good source that heavier weight motor oil is "thicken" by additives. Since synthetic have very long and strong polymer chain it is OK to run significantly lower viscosity when the spec calls for heavier petrolium based.

The Mini's official weight is 5W30 and am quite sure most BMW is the same too.

Why are people putting down Mobil 1? I have used it for years and it was one of the first synethic.

- Vince

http://gipsyflies.home.comcast.net 1989 Vanagon GL Camper 1993 Mazda Miata (for sale) 1996 Land Rover Discovery 2005 Mini Cooper S

-----Original Message----- From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of Chuck Mathis Sent: Sunday, September 12, 2004 7:16 AM To: vanagon@GERRY.VANAGON.COM Subject: Re: Disappearing Coolant - Head Lean?

Vince;

Sounds like you are definitely leaking from the sensor area. When I dealt with that problem the o-ring was intact and very subtle while the sensor was leaking. If you've got dry contacts it probably is the o-ring but it could also be a crack in the tank at the threads. I'll keep my fingers crossed for you.

Are you really running Mobil 1 5W-30 in a WBX or is that a typo? The WBX usually requires something in the range of a 40-50 weight. I ran Mobil 1 15w-50 for years but recently switched to Castrol Syntec 5W-50 cause all the FLAPS were out of the heavy Mobil 1.

Chuck '85 Wolfsburg Westy - 'Roland the Road Buffalo'

Vince wrote:

Date: Sat, 11 Sep 2004 15:16:32 -0700 From: Vince S <gipsyflies@COMCAST.NET> Subject: Disappearing Coolant - Head Lean?

I was performing my annual tune up / oil change on my 89 Westy today. I started off by checking the oil level but I notice the coolant filler/reservoir tank is totally empty. What happened? I filled it a couple of months back when it was just below the Min mark and now it is bone dry. My immediate thought of the dreaded inevitable water boxer head leak which I have been lucky so far.

I crawled under the engine to see if there is signs of the leak. Sure enough the left rear header pipe is wet and it is unmistakably coolant. Very carefully I visual inspected the head on the driver side and there is no sign of coolant residue. Suspecting the water pump I check that too and there is also no sign of coolant.

Time to look from above so I open the rear engine hatch. I can see much trace of coolant clinging to the outside of coolant expansion tank, especially what looks to be the seam of the top and bottom halves. The plastic expansion tank must developed a leak at the welded seam, I thought.

I more carefully inspected the tank with better lighting and I notice the pool of coolant in the dimple at the top of the tank where the coolant level sensor resides. Without the necessary part to repair it I didn't want to disrupt the area. I just wanted to see if the leak is from within the sensor, or leaking between the sensor and the tank. I unplugged the sensor connector and it is bone dry on the contacts so it appear the lead is between the sensor and the tank. According to the Bentley there is a o-ring. The o-ring must became harden over all this years and now does not seal under pressure. Since it is weekend I decided not to unscrew the sensor in case I need to use the vehicle during the weekend.

I was relief that it is not the dreaded head gasket leak.

I proceed to a complete tune up including changing the spark plugs, distributor rotor, distributor cap, air filter, oil filter and change the oil with Mobil 1 5W30 synthetic.

I also thoroughly wiped down the ignition wire with soap and water as well as every parts I can clean in the engine bay. If there is a cleanest Vanagon engine bay award I think I stand a good chance of winning it.

- Vince

http://gipsyflies.home.comcast.net 1989 Vanagon GL Camper 1993 Mazda Miata 1996 Land Rover Discovery 2005 Mini Cooper S


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.