Date: Sat, 22 Jan 2005 20:13:40 -0500
Reply-To: Dennis Haynes <dhaynes@OPTONLINE.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Dennis Haynes <dhaynes@OPTONLINE.NET>
Subject: Re: hole saws/floor cutting
In-Reply-To: <989ea5a2050122163540bad153@mail.gmail.com>
Content-type: text/plain; charset=US-ASCII
http://g.msn.com/9SE/1?http://www.toolfetch.com/tools/category/Pneumatic
-Tools/Punch-Kits.html&&DI=293&IG=b4ac87290820448ca4897a8474ef70d4&POS=1
&CM=WPU&CE=1&CS=AWP&SR=1
Here are the tools to put a hole in the Vanagon Floor. Bring $$.
Dennis
-----Original Message-----
From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf
Of TJ Hemrick
Sent: Saturday, January 22, 2005 7:36 PM
To: vanagon@GERRY.VANAGON.COM
Subject: hole saws/floor cutting
This is a highly opinionated response so take it with a grain of
salt. Being a man, I'll use any excuse to buy a new tool. Now I've
got several tools from Harbor Freight and they serve me very well and
at a great cost. BUT, if I'm going to be cutting a hole in my pride
and joy, I'm going to sell my left #@% to pay for the best hole saw I
can find. I'll always find a use for it or other blades if I find a
great one that allows blade changes and if I need to help someone else
out, I'm prepared. Especially after comments like, "A hole saw will
work but is tricky to control in that space. Done it. Extra damaged
knuckles job. That in itselft says to me, "go big" Now that doesn't
mean spend the most, but good tools usually cost more. Good luck and
safe drilling as bits tend to grab and stop when going through sheet
metal. The bigger the bit, the bigger the grab. When that bit grabs,
it stops right NOW. The drill will turn in your hand so use the
slowest big drill you can find with an extension hand. Leave plenty
of cord available as it will wrap around your arms. My buddies dad
had a bit grab after breaking through sheet metal. The bit stopped,
the drill didn't, it wrapped the cord around both arms and he couldn't
let go of the trigger fast enough and broke both wrists right then and
there. Crazy old guy drove himself to the hospital. Don't ask, I
didn't.
This is one case I disagree with, "Use a cheapie hole saw set from
harbor freight or similar. "
just my.02
TJ
Date: Sat, 22 Jan 2005 11:19:13 -0700
From: jimt <camper@TACTICAL-BUS.INFO>
Subject: Re: cutting hole in van floor
On 1/22/05 11:01 AM, "Gerald Masar" <azsun99@EARTHLINK.NET> wrote:
> I need to cut a 50mm (slightly less than 2") hole in the floor of my
'90 =
Westy
> to
> install a gas furnace. It will be in the back corner of the small
compart=
ment
> to the
> left of the fridge. I looked at holesaws yesterday, and besides being
> expensive to buy
> one for just this job, I am wondering how well they would work on the
une=
ven,
> ribbed
> surface of the van floor. And the hole will come out 1/8" away from
the m=
ain
> side
> beam.
> Any hints, tips, suggestions on how to do this?
> Thanks
> Jerry
>=20
>=20
A hole saw will work but is tricky to control in that space. Done it.
Extra damaged knuckles job. Coming out the bottom I suspect a propex
furnace. Use a cheapie hole saw set from harbor freight or similar. A
couple buck throw away.
=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95
=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95=95
jimt
Planned insanity is best.
Remember that sanity is optional.
http://www.tactical-bus.info (tech info)
http://www.westydriver.com