Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (January 2005, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Tue, 25 Jan 2005 12:34:57 -0800
Reply-To:     mark drillock <drillock@EARTHLINK.NET>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         mark drillock <drillock@EARTHLINK.NET>
Subject:      Re: Question about Mass Air Flow Sensor
Comments: To: Kenneth Wilford <kenwilfy@COMCAST.NET>
In-Reply-To:  <002301c5030c$469296b0$650fa8c0@DELL>
Content-Type: text/plain; charset=us-ascii; format=flowed

Ken, according to my Jetta Bentley for that year, the MAF sensor red/blue wire you refer to should have power whenever the fuel pump is running. It's power comes from current track 16, brought to there on relay panel track "a" which comes from the fuel pump relay output leg, 4/87 on relay J17. The ECU controls whether the fuel pump runs, by controlling the ground leg of the fuel pump relay coil 3/85 of relay J17. Of course with a conversion the installer may mouse around with the fuel pump control but it is best to do it like the factory did so the pump shuts off unless the engine is running normally or trying to start. There are a few other devices that also get power from the same source so make sure that the other devices with a wire of the same color are also connected to it.

Mark

Kenneth Wilford wrote:

>I think I have found a problem with the wiring harness on the conversion >I am working on. The wiring harness is from a 97 Jetta with the 2.0l >ABA engine. Anyway the wiring harness has a four wire plug on the mass >air sensor. One of the wires is red with a blue stripe. If you have >the Jetta Bentley Manual it is on page 97-297. This wire goes to a >group of other wires that are the same color and they hook to what is >called "Plus connection in Multiport Fuel Injection wiring harness". On >the wiring diagram this is called E7 however the wiring diagram also >calls it 87a. What I think is going on is that this wire is the power >for the heated air mass sensor. But I don't want to hook up power to it >if it isn't supposed to get power as I don't want to fry anything. Can >anyone help me figure this out. Also is this wire supposed to be full >time hot or just hot when the ignition on. > >This wire was cut and not hooked to anything when I got the conversion. >The van runs but only when it is warm outside and also it doesn't seem >to have a lot of power. > >Sorry but I am not super familiar with the whole mass air sensor thing. > >Any help you can give would be apreciated. > >Thanks, >Ken Wilford >John 3:16 >http://www.vanagain.com >http://www.strictlyvwauctions.com >http://www.eurovan.org >http://www.vwcabrio.org >Phone: (856)-327-4936 >Fax: (856)-327-2242 > > >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.