Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (April 2005, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 6 Apr 2005 09:17:50 -0400
Reply-To:     Benoit <huotb@VIDEOTRON.CA>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Benoit <huotb@VIDEOTRON.CA>
Subject:      Re: Thechnical clutch question....(the answer may help many to
              save some$$$)
Comments: To: dhaynes@optonline.net
In-Reply-To:  <781ce22781e931.781e931781ce22@optonline.net>
Content-type: text/plain; charset=us-ascii; format=flowed

Well......i don't agree, not that you are not right...but something is Wrong in there... Other car i work on have a second spring in the housing to help the hydro / cable system to bring the bearing back.

Another thing, some vans are worse than others. An 84 that i worked on just had a bearing failiure/seizure after 10k miles. On some of the van i work on the bearing is to dificult to push in. I wonder if some kind of air pocket make is way is the system wile vans are left without a clutch for some time in the shop.

Anyway, i will bleed the system just in case. am blamming old clutch cylinder.....

Thanks, Ben

dhaynes@optonline.net wrote:

>The Clutch system does not have the ability to pull the release bearing away from the pressure plate. In fact, the operating cylinder, (slave) has a spring which will always put some pressure on the bearing. This is normal. Yes it does keep the bearing spinning but the load is very light. The release bearing can still last well past 100K and usuaully something else will fail reqiuring the the clutch to need service first. > >Dennis > >----- Original Message ----- >From: Benny boy <huotb@VIDEOTRON.CA> >Date: Wednesday, April 6, 2005 1:15 am >Subject: Thechnical clutch question....(the answer may help many to save some$$$) > > > >>Ok. short explanation: >>The clutch pedal spring should bring back the clutch bearing in >>front (Front >>is front/ transmission side), moving him away from the clutch >>basket when >>the pedal is not press... >>That pressure bearing is NOT design to always touch the basket >>(Pressureplate if you like) in normal driving condition, but only >>when the clutch >>pedal is pressed... >> >>The system is hydrolic, so this is basically a push pull >>situation...thebasket is not suppose to be the one pushing that >>bearing, this bearing >>should be free and not touching the basket when the pedal is not >>push, fully >>on the transmision side and not the basket side. >> >>But lately, on 3 vans...that bearing is way out of is shaft (rear >>when it >>should be in front!!!), pedal spring is ok, so basicaly i have to >>push the >>engine/clutch in the tranny wile the bearing is out and should be >>in, in >>other words, pushing the bearing in with the clutch basket when it >>shouldalready be IN!!!!!, that mean that the basket is pushing the >>bearing in. >>Hard to explain witout a picture but i hope you understand. >> >>My conclusion: Air in the clutch hydro line or faulty clutch rear >>valve/piston!Something is wrong there, that bearing wile wear out >>to fast if it's >>spinning all the time.. >> >>Anyone with an answer to my question....am waithing!!! >> >>Cheers, Ben >>http://www.benplace.com/vanagon_engine6.htm >> >> >> > > > > >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.