Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (April 2005, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sat, 16 Apr 2005 08:09:17 -0700
Reply-To:     dylan friedman <insyncro@YAHOO.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
Comments:     DomainKeys? See http://antispam.yahoo.com/domainkeys
From:         dylan friedman <insyncro@YAHOO.COM>
Subject:      Re: Painting exhaust pipes?
Comments: To: John Rodgers <inua@CHARTER.NET>
In-Reply-To:  6667
Content-Type: text/plain; charset=us-ascii

I use 316 stainless bolts and washers with brass nuts on all of my exhausts. RED locktite the nuts while installing and the exposed threads after tightening. They have not moved unless I have heated them with a torch first.

dylan --- John Rodgers <inua@CHARTER.NET> wrote: > Jeff Oxroad wrote: > > >In a message dated 4/14/2005 9:11:17 PM Pacific > Standard Time, > >jfarrugi@UMICH.EDU writes: > > > >as for the > >bolts non-magnetic stainless is the way to go. > > > > > > > >My experience with stainless steel bolts in the > exhaust system is they do > >not rust--but they do vibrate loose. this is in > case you were referring to > >stainless steel bolts. this creates a frustrating > situation. May be a way to > >solve it? > >Best > >Jeff > > 83.5 Westy > >LA,CA > > > > > > > > > You might poke around and try and find a catalog on > the web for AN > hardware for airplanes. There are there are inside > and outside serrated > locking washers, and bendable tab locking devices > that are available > through the industry. If worse comes to worse, you > can use a sharp > pointed tool and a hammer and "Stake" the threads of > the bolt or nut so > they cannot turn unless you actually put pressure on > it with a wrench. > Staking - striking the sharp tool with the hammer - > expands the metal at > that point making it impossible for the bolt or nut > to turn. Forceably > turning with a wrench will straighten the metal > again so the parts will > turn again. The absolute way to secure a nut or bolt > is to install a > properly made safety wire tie. There is no way a nut > or bolt will turn > against the restraint of the stainless steel wire. > > Regards, > > John Rodgers >

Dylan Friedman

insyncro@yahoo.com

91 Syncro Westy GL 91 Syncro L 90 Carat 89 Wolfsburg GL

__________________________________ Do you Yahoo!? Plan great trips with Yahoo! Travel: Now over 17,000 guides! http://travel.yahoo.com/p-travelguide


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.