Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (June 2005, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Tue, 21 Jun 2005 10:12:14 -0700
Reply-To:     Mike Jeffrey <oldbus@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Mike Jeffrey <oldbus@GMAIL.COM>
Subject:      Re: What goes here?
Comments: To: "dhaynes@optonline.net" <dhaynes@optonline.net>
In-Reply-To:  <c2d7dfc2edc1.c2edc1c2d7df@optonline.net>
Content-Type: text/plain; charset=ISO-8859-1

Ah! Interesting - thank you Dennis :) I have two left heads then, as the hole also exists on the left side. Are there any issues with simply putting a bolt in there (to keep out dirt and dust)? If not, I'll just get a shorter bolt than the one I currently have, and snug it in there.

Thanks for giving me peace of mind! Mike.

On 6/21/05, dhaynes@optonline.net <dhaynes@optonline.net> wrote: > Somehow you have left side cylinder head on the right side of the engine. That hole is for the temp senor. If you have two left side heads, no problem. If not, then install the sensor on that side and extend the wire. There is no problem if you leave the hole empty except a slight loss of cooling air. > > Dennis > > ----- Original Message ----- > From: Mike Jeffrey <oldbus@GMAIL.COM> > Date: Monday, June 20, 2005 11:07 pm > Subject: Re: What goes here? > > > Oops! Sorry about that - it's a 1983 2.0 liter, fuel-injected > > California. Found a picture of the old bolt and the old engine: > > > > http://www.californiabackcountry.com/IMG_0237.jpg > > > > Thanks for your help! > > Mike. > > > > > > On 6/20/05, Dennis Haynes <dhaynes@optonline.net> wrote: > > > What engine/year? > > > Could you provide a little better description? > > > > > > Dennis > > > > > > -----Original Message----- > > > From: Vanagon Mailing List [vanagon@gerry.vanagon.com] On Behalf > > > Of Mike Jeffrey > > > Sent: Monday, June 20, 2005 3:52 PM > > > To: vanagon@GERRY.VANAGON.COM > > > Subject: What goes here? > > > > > > Hello listers, > > > > > > What goes into the big threaded hole to the left (towards the > > back) of > > > intake #2 (right hand side, towards back)? I have a plain old bolt > > > that came out of the same hole in my old block... when I go to > > thread> it into the new block, it hits something inside before it > > snugs all > > > the way down. > > > > > > If I remember correctly, it looks like the same kinda hole that > > > accepts the oil temp sensor in front of intake #3. > > > > > > Thanks! It is, quite literally, the last bolt that needs bolting > > > before this engine gets started for the very first time! > > > > > > Mike. > > > > > > > > > > > > >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.