Date: Wed, 22 Jun 2005 18:25:06 -0500
Reply-To: Stan Wilder <wilden1-1@SBCGLOBAL.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Stan Wilder <wilden1-1@SBCGLOBAL.NET>
Subject: Santa Fe / Albuquerque area folks
Content-Type: text/plain; charset="iso-8859-1"
I'll be passing through the Santa Fe / Albuquerque area Thursday and will
probably be hanging around Friday, possible Saturday too.
If you live in the area, send me your phone and I'll try to catch a few
minutes with you while I'm rambling between the two cities.
Reply before 9 PM this evening, Wednesday June 22snd because I'll be flying
out from Dallas at 10 PM to Denver to pick up a Porsche that I'll be driving
back to Dallas.
Stan Wilder
Engine Ceramics
214-352-4931
www.engineceramics.com
----- Original Message -----
From: "jake beaulieu" <jbeaulie@ND.EDU>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Tuesday, June 21, 2005 6:31 PM
Subject: Re: What goes here?
> I have a new Boston Bob engine in my 82 AC Westy. When it came the
> passengers side head had the threaded hole for the temp sensor. I had
> recently replaced this sensor, so I just screwed the old one in the hole
to
> close it up. I can't imagine why a bolt wouldn't work just as well.
>
> Jake
>
> -----Original Message-----
> From: Vanagon Mailing List [mailto:vanagon@GERRY.VANAGON.COM] On Behalf Of
> Mike Jeffrey
> Sent: Tuesday, June 21, 2005 12:12 PM
> To: vanagon@GERRY.VANAGON.COM
> Subject: Re: What goes here?
>
> Ah! Interesting - thank you Dennis :) I have two left heads then, as
> the hole also exists on the left side. Are there any issues with
> simply putting a bolt in there (to keep out dirt and dust)? If not,
> I'll just get a shorter bolt than the one I currently have, and snug
> it in there.
>
> Thanks for giving me peace of mind!
> Mike.
>
> On 6/21/05, dhaynes@optonline.net <dhaynes@optonline.net> wrote:
> > Somehow you have left side cylinder head on the right side of the
engine.
> That hole is for the temp senor. If you have two left side heads, no
> problem. If not, then install the sensor on that side and extend the wire.
> There is no problem if you leave the hole empty except a slight loss of
> cooling air.
> >
> > Dennis
> >
> > ----- Original Message -----
> > From: Mike Jeffrey <oldbus@GMAIL.COM>
> > Date: Monday, June 20, 2005 11:07 pm
> > Subject: Re: What goes here?
> >
> > > Oops! Sorry about that - it's a 1983 2.0 liter, fuel-injected
> > > California. Found a picture of the old bolt and the old engine:
> > >
> > > http://www.californiabackcountry.com/IMG_0237.jpg
> > >
> > > Thanks for your help!
> > > Mike.
> > >
> > >
> > > On 6/20/05, Dennis Haynes <dhaynes@optonline.net> wrote:
> > > > What engine/year?
> > > > Could you provide a little better description?
> > > >
> > > > Dennis
> > > >
> > > > -----Original Message-----
> > > > From: Vanagon Mailing List [vanagon@gerry.vanagon.com] On Behalf
> > > > Of Mike Jeffrey
> > > > Sent: Monday, June 20, 2005 3:52 PM
> > > > To: vanagon@GERRY.VANAGON.COM
> > > > Subject: What goes here?
> > > >
> > > > Hello listers,
> > > >
> > > > What goes into the big threaded hole to the left (towards the
> > > back) of
> > > > intake #2 (right hand side, towards back)? I have a plain old bolt
> > > > that came out of the same hole in my old block... when I go to
> > > thread> it into the new block, it hits something inside before it
> > > snugs all
> > > > the way down.
> > > >
> > > > If I remember correctly, it looks like the same kinda hole that
> > > > accepts the oil temp sensor in front of intake #3.
> > > >
> > > > Thanks! It is, quite literally, the last bolt that needs bolting
> > > > before this engine gets started for the very first time!
> > > >
> > > > Mike.
> > > >
> > > >
> > > >
> > >
> >
> >
|