Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (September 2005, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sun, 25 Sep 2005 08:51:07 -0700
Reply-To:     Shawn Wright <swright@ZUIKO.SLS.BC.CA>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Shawn Wright <swright@ZUIKO.SLS.BC.CA>
Subject:      Re: Vibration under acceleration - CV joints?
In-Reply-To:  <4336BC89.1090409@charter.net>
Content-type: text/plain; charset=US-ASCII

Thanks John. I will try swapping the axles just in case, and if I encounter any loose bolts, then I'll know. But this has been a long standing probably, so I imagine loose bolts would have fallen out by now... Sounds like I will need to tear them down at some point and find the bad one(s).

On 25 Sep 2005 at 10:04, John Rodgers <inua@CHARTER.NET> wrote:

> Check the CV mount bolts for security. It any of them back off the CV's > can make the vibration.throbbing you speak off. I wnet through that with > my 88 GL. I discovered loose bolts on one of the outboard CV's. Torquing > the bolts stopped the noise. If they are secure, then it is a guess as > to where to look next short of pulling, cleaning and inspecting the > CV's. It is a realatively easy job, but does take time. If you haven't > had these serviced in a known period of time, now would be the time to > do it. When I did mine, I found pitting in the balls and the race both. > Though they seemed tight, the pitting was an indication it was time to > replace. I installed new Lobros all the way around. > > Good Luck, > > Regards, > > John Rodgers > 88 GL Driver > > Shawn Wright wrote: > > >My '88 Westy has had a steadily increasing throbbing/vibration under load > >and acceleration for a few years, which I assumed was engine mounts. > >Now that I have replaced the engine, transmission, and mounts, it is still > >there. I'm guessing the only remaining culprit could be the CV joints, right? > >Is there a reliable way to find the worn joints without removing and > >inspecting? Should I try just swapping the drive shafts side to side? > > > >ps: It was a stock 2.1L with 4speed, now is a 1.6TD with 5 speed. > > > >Shawn Wright > >http://zuiko.sls.bc.ca/~swright > >'85 Jetta D > >'88 Westy 1.6TD 5 speed > > (see progress at http://members.shaw.ca/vwdiesels) > >'82 Diesel Westy > > > > > > > > >

Shawn Wright http://zuiko.sls.bc.ca/~swright '85 Jetta D '88 Westy 1.6TD 5 speed (see progress at http://members.shaw.ca/vwdiesels) '82 Diesel Westy


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.