Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (May 2006, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Sun, 14 May 2006 15:44:25 -0400
Reply-To:   neil <goofymuso@YAHOO.CA>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   neil <goofymuso@YAHOO.CA>
Subject:   Re: CV removal tips?
Comments:   To: Dennis Haynes <dhaynes@optonline.net>
In-Reply-To:   <000201c67789$fd46fa70$6400a8c0@masterpc>
Content-Type:   text/plain; charset=iso-8859-1

Was joking about bigger and hammer.

Next time I won't joke around with tech stuff. In spite of having included the "wink smile" ----> ;) things can be misunderstood.

But of course. Pounding on end of driveshaft with a hammer is not the solution. And yes it would mushroom the end no matter how good/strong the steel is.

What is a "dead blow" hammer? A hard yet non metallic hammer?

I wonder why it is so stuck? Can things get corroded in there? Torque twisting things around?

Neil.

--- Dennis Haynes <dhaynes@optonline.net> wrote:

> Once you take a hammer to the end of a drive shaft, > you could be done. > The end of the shaft will mushroom out making thins > harder, if not > impossible. At a minimum, use a brass rod or a dead > blow hammer. A gear > puller is a much better option. A press is an ideal > solution. > > Dennis > > > -----Original Message----- > From: Vanagon Mailing List > [mailto:vanagon@gerry.vanagon.com] On Behalf > Of neil > Sent: Sunday, May 14, 2006 2:04 PM > To: vanagon@GERRY.VANAGON.COM > Subject: Re: CV removal tips? > > Hi Shawn. > > A bigger hammer? ;) > > I've never done this particular job before but..... > > As the drive shaft should be allowed to move in > vice, > make sure cv assembly is not "bouncing" around on > vice > jaws when driving shaft down/out. i.e. it stays in > place when you are tapping. Solid impact/contact is > crucial when drifting things out. And.... > > Don't know if it's wise, but maybe a helper could, > from below, pull down on driveshaft when you are > tapping from above. I'm sure others will correct me > if > that's a dangerous idea..... > > ;) > > > Neil. > > > --- Shawn Wright <swright@ZUIKO.SLS.BC.CA> wrote: > > > After just re-installing my axles, I find one of > the > > old boots (I replaced two of > > four) has a small hole allowing little blobs of > > grease out. This was one of the > > CVs I could not get off the shaft, so I put it > back > > on. I suppose I could pull > > the *other* CV and install the boot from the other > > end, but I'd rather figure > > out how to get the stuck CVs off. I have removed > the > > circlip and tried tapping > > the end of the shaft with a cold chisel while the > > outer joint was supported in > > a vise, but it would't budge. Both my inboard CVs > > are now stuck like this, > > and will wear out eventually... > > Any ideas appreciated. > > > > > > Shawn Wright > > http://members.shaw.ca/vwdiesels > > '88 Westy 1.6TD 5 speed > > '85 Jetta Diesel 1.6NA > > > > > Neil Nicholson. > 1981 air cooled Westfalia. > Cheap-o web site: > > http://www.members.shaw.ca/tubanick/welcomewesty.html > > __________________________________________________ > Do You Yahoo!? > Tired of spam? Yahoo! Mail has the best spam > protection around > http://mail.yahoo.com > > >

Neil Nicholson. 1981 air cooled Westfalia. Cheap-o web site:

http://www.members.shaw.ca/tubanick/welcomewesty.html

__________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.