Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (May 2006, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sun, 28 May 2006 05:47:34 -0700
Reply-To:     Dave Szurszewski <meisterburgus@YAHOO.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Dave Szurszewski <meisterburgus@YAHOO.COM>
Subject:      Re: Install Auto transmission to final drive problem
In-Reply-To:  <6.0.3.0.0.20060528082347.032fa140@buncombe.main.nc.us>
Content-Type: text/plain; charset=iso-8859-1


Turning the crankshaft does turn the smallest shaft.
But I think it is the transmission driveshaft (I think
Bentley refers to is as the hydraulic driveshaft) and
then there is the pinion driveshaft.  I can adjust the
position of the smallest (pump driveshaft) by turning
the crank and adjust the outer largest (pinion) by
turning both drive axle mounts.  But can not get to
the middle shaft.  I think it is driven by the torque
converter.


This looks like it is matter of 'just keep trying
until it fits'


Thanks,
Dave






--- Edward Maglott <emaglott@BUNCOMBE.MAIN.NC.US>
wrote:


> The smallest shaft runs all the way from the torque
> converter to the pump
> in the AT, which is at the far, far end by the ATF
> cooler.  There are
> splines on both ends of that shaft that have to
> engage.  Try turning the
> crankshaft to see if that helps them to engage.
> That's all that comes to
> mind.
>
> Edward
>
> At 08:13 AM 5/28/2006, Dave Szurszewski wrote:
> >Hello,
> >I've been reading the list since last Nov. when I
> >bought my Westy.  I've finally come across
> something I
> >can't find an answer to in the archives.
> >
> >I've dropped the entire drivetrain to do
> headgaskets
> >and other maintenance.
> >As part of this I have split the Auto tranny from
> the
> >final drive to replace
> >the o-ring and fiber gaskets.
> >Problem is I can't get the transmission back on.
> The
> >driveshafts will not
> >mate up ,preventing the tranny from seating all the
> >way.  Is there some
> >trick to this?   I didn't find anything in the
> bentley
> >(unless I'm just not seeing them).  I did not
> separate
> >the transimission from the engine.
> >
> >My van is an 88 westy.  Any advice appreciated.
> >
> >
> >Thanks,
> >Dave
> >
> >
> >
> >__________________________________________________
> >Do You Yahoo!?
> >Tired of spam?  Yahoo! Mail has the best spam
> protection around
> >http://mail.yahoo.com
>




__________________________________________________
Do You Yahoo!?
Tired of spam?  Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!

Return to the archives @ gerry.vanagon.com

The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.