Date: Mon, 19 Jun 2006 18:08:54 -0700
Reply-To: Robert Fisher <refisher@MCHSI.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Robert Fisher <refisher@MCHSI.COM>
Subject: Re: A throttle puzzle Pictures of Insatll on Automatic
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=response
So I have an '87 GL with what I believe is the stock cruise control. I don't
know what the differences are in the throttle body itself between your '84
and my '87 but perhaps it may be easier for you to obtain the later one or
at least some parts from it and adapt it to your purposes.
Here are some pics, the names are (hopefully) self-explanatory:
http://home.mchsi.com/~refisher/87_stock_cruise_control_long_view.jpg
http://home.mchsi.com/~refisher/closeup_of_accel_rod_guide.jpg
http://home.mchsi.com/~refisher/longer_view_of_accel_rod_guide.jpg
http://home.mchsi.com/~refisher/without_cruise_control_linkage.jpg
As you can see the 'pin' or 'guide' actually has a threaded bore into which
you could presumably install a small bolt with which you could do what you
had in mind; I would be concerned about the strength of the connection but
that could be successfully addressed, I think. I don't recall ever having
removed that guide, so I couldn't tell you if it's supposed to be that way
or if it's upside down or what...
Otherwise you could perhaps mount your actuator wire in such a way (coming
in from the left) that you could use the stock linkage or at least the
post/ball to which it connects.
Hope that helps.
Good luck,
Robert
----- Original Message -----
From: "Mike Elliott" <j.michael.elliott@GMAIL.COM>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Monday, June 19, 2006 4:10 PM
Subject: Re: A throttle puzzle Pictures of Insatll on Automatic
> Hi Loren,
>
> Thanks for posting those pictures. Nice work.
>
> I considered drilling a hole in the throttle arm to affix the servo
> cable in exactly the same spot you drilled yours. I hesitated to follow
> through on that idea because the installation manual for the Audiovox
> cruise control says that the maximum travel for the servo cable -- from
> idle to full throttle -- is 45mm. According to my rough measurements, if
> the servo cable is attached to that attractive spot, it is so far from
> the center of rotation of the throttle arm that the servo cable has to
> travel more than 50mm, and maybe as much as 55mm, to swing the arm from
> the rearward idle position to the fully-forward full throttle position.
>
> This suggests that, when climbing a grade (and we got 'em in
> California), the servo would not be able to achieve that last 5mm to
> 10mm of pull needed to reach the fully forward position.
>
> --
> Mike "Rocket J Squirrel" Elliott
> 71 Type 2: the Wonderbus
> 84 Westfalia: Mellow Yellow ("The Electrical Banana")
> 74 Utility Trailer. Ladybug Trailer, Inc., San Juan Capistrano
> KG6RCR
>
>
>
> On 6/19/2006 3:40 PM Loren Busch wrote:
>> There was a lot of discussion yeaterday on how to install the
>> Audiovox CCS 100 cruise control when you have an automatic
>> transmission. Here are some pictures showing the attachement to the
>> throttle and also the location of the serv box. Someone was asking
>> about where to put the serv last week.
>> http://www.pbase.com/labusch/cruise