Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (December 2006, week 5)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sat, 30 Dec 2006 23:26:36 +0000
Reply-To:     dhaynes@OPTONLINE.NET
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Dennis Haynes <dhaynes@OPTONLINE.NET>
Subject:      Re: Manifold vacuum specs?-Leak down testing
Comments: To: Geza Polony <gezapolony@SBCGLOBAL.NET>
In-Reply-To:  <vanagon%2006123012200936@GERRY.VANAGON.COM>
Content-Type: text/plain; charset=us-ascii

A proper leak down test will tell you all you need to know. After measuring the leak down, wit the engine restrained, you can by pass the tester and directly pressurize the cylinders with shop air and you will be able to hear where the internal leakage is occurring. Remove the airflow meter and coolant pressure cap while doing this. If the air forces coolant out of the expansion tank, then you know you have an internal leak. If you hear air leaking through the crank breather, it is getting past the pistons/rings/some leakage is normal past the ring gaps. If your hear leakage through the intake, you have an intake that is not seating and if through the exhaust, bad exhaust valve.

Poor valve seating is usually the result of worn guides. Loosening the lifters may provide temporary relief but this is not the fix. If the lifters are not noisy, it is unlikely they are a problem unless you excessively high oil pressure or weak valve springs.

Dennis

----- Original Message ----- From: Geza Polony Date: Saturday, December 30, 2006 12:31 pm Subject: Manifold vacuum specs? To: vanagon@GERRY.VANAGON.COM

> Volks-- > > > I've been trying to sleuth out yet another prob on my '84 1.9: > erratic idle, > compression noise under load, low (er) power on hills, harder > starting when > hot. I'm toying with the idea that there's a lifter problem, a valve > problem, or worse, ie., rings or head gaskets. > > Now. I went out and got a vacuum guage and compression tester. > However, I > can't find the correct specs for vacuum readings ANYWHERE in the > Bentley or > the Haynes manuals. Am I missing something? > > Nearest I can find, searching the archives, is that 8 in. is too > low. Is > that right? What's the acceptable range? > > What else am I looking for in this vacuum test? Just vacuum level? > > Is there a way to pinpoint problems with it, or does it just > tell you > "there's a problem?" > > I want to try backing out the valve adjustment screws to give a > .06 lash as > suggested by some of the heavyweights here (and in Bentley) but > understandit's better to read vacuum and compression before and > after. > Thanks to all-- > > Geza >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.