Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (February 2007, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Wed, 14 Feb 2007 12:15:56 -0800
Reply-To:   "mike ." <mwmiller@CWNET.COM>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   "mike ." <mwmiller@CWNET.COM>
Subject:   Re: Jalousies Windows for a Vanagon
Comments:   To: Daniel Stevens <dosteven@SYR.EDU>
In-Reply-To:   <s5d2fbc5.029@gwia203.syr.edu>
Content-type:   text/plain; charset="US-ASCII"

I have the windows [and have had for several years] but can't find the time and money to put them in. So keep this thread up please.

Mike

On 2/14/07 9:08 AM, "Daniel Stevens" <dosteven@SYR.EDU> wrote:

> I haven't finished mounting mine just yet. BUT.. with the middle side window > out.. > I can "FIT" the jalousie window in the hole fairly securely. > (it's been sitting there unattended for most of the summer as I drive the > project in and out of the garage) > My idea is to cut NEITHER the jalousie or the van body,. but to make 2 filler > strips (aluminum) for the top&bottom gaps. > and use some TORX security screws to fasten to an interior trim piece i've yet > to imagine/create. > the interio panel can either be wood or formed fiberglass i've yet to decide. > I plan on using automotive/commercial Urethane sealant for the frame to body > seal. very strong hold but nonpermament. > > I'll document my method when I get back into it, when all this dang upstate NY > snow recededs. > > Dan in Syracuse > *----------------------------------------------------------------------------- > ---------------------- > > Date: Sat, 10 Feb 2007 21:16:46 -0500 > From: Pascal Giasson <pascal.giasson@GNB.CA> > Subject: Re: > > I have followed the instructions described in this link > http://www.everybus.com/dworkin/vgon_jalousie/ > to replace my driver side slider with a jalousie out of a 73 westy but > something does not jive. The two vertical pieces that are 3/4" wide do not > seam to accomodate the 1/4" filler piece that is supposed to be sandwiched > between them. The 1/4" filler piece protrudes out most of the way. It > looks like the 3/4" pieces should be 1" wide to be able to accomodate the > filler piece. HAs anybody who has done this run into the same problem? I > don't have my slider out and dont plan on taking it out for a while, but > does anyone know the measurments of the slider on the driver side? Is it > in fact 42 3/8" X 16 3/4" as these instruction say? > BTW the router and tablesaw worked great at cutting the aluminium. > Thanks > Pascal


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.