Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (April 2007, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sat, 21 Apr 2007 00:36:29 -0400
Reply-To:     Dennis Haynes <d23haynes57@HOTMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Dennis Haynes <d23haynes57@HOTMAIL.COM>
Subject:      Re: Oil Pressure Switch R&R
Comments: To: RAlanen@AOL.COM
In-Reply-To:  <c96.d8088b4.3359ee37@aol.com>
Content-Type: text/plain; format=flowed

Remove the water pump pulley and use a breaker bar instead of a ratchet.

Dennis

>From: Frank Condelli <RAlanen@AOL.COM> >Reply-To: RAlanen@AOL.COM >To: vanagon@GERRY.VANAGON.COM >Subject: Re: Oil Pressure Switch R&R >Date: Fri, 20 Apr 2007 06:21:43 EDT > >In a message dated 19/04/2007 2:55:12 P.M. Eastern Standard Time, >LISTSERV@GERRY.VANAGON.COM writes: > >I can usually perform most any repair on the venerable 1.9 or 2.1 engine. >But here's one where I've become stumped. The "high side" oil pressure >switch located just below the crank pulley and next to the oil filter >mount >has developed a crack in the plastic and is producing a consistent drip, >thus oiling up the backside of "Ole Putt". How does one access this >little >jewel and replace it with the engine in the vehicle? A 24mm deep socket >would be perfect except the heat shield prevents the attachment of a >ratchet >to unscrew it off (and of course screw the new one on). Right now it >looks >like the cat and muffler would have to be removed and the heat shield >removed to get the extra room, but if anyone else has done this another >way, >I'm all ears. > >Because the 2.1 is installed in my 84 Westy, there is no "Dynamic Oil >Pressure Buzzer System", so the switch just acts as a plug. I would >probably replace it with an appropriate length 10 x 1.0 threaded bolt >sealed >with teflon tape. > > > > > >Jim, you should be able to use your 24mm socket with a ratchet or breaker >bar. The trick is to bend the muffler heat shield a bit to get the >clearance. > But, I see you have this 2.1 in a '84 unless you installed the heat >shield >from the 2.1 Van. The heat shields are different so some modification of >that ' 84's heat shield will be necessary. > >Cheers, > >Frank Condelli >Almonte, Ontario, Canada >'87 Westy, '90 Carat, '87 Wolfsburg (Forsale) & Lionel Trains (_Collection >for sale_ (http://members.aol.com/Fkc43/trainsal.htm) ) >_Frank Condelli & Associates_ (http://members.aol.com/Fkc43/busindex.html) >- Vanagon/Vanagon Westfalia Service in the Ottawa Valley >_Vanagon Stainless Steel Exhaust Systems_ >(http://members.aol.com/Fkc43/stebro.htm) >_BusFusion_ (http://members.aol.com/BusFusion/bfhome.htm) a VW Camper >camping event, Almonte, ON, June 07 ~ 10, 2007


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.