Date: Sun, 6 May 2007 21:42:54 -0700
Reply-To: David Kao <dtkao0205@YAHOO.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: David Kao <dtkao0205@YAHOO.COM>
Subject: Re: oil pressure
In-Reply-To: <Pine.LNX.4.64.0705060445230.1980@goldenaxe.gpcc.itd.umich.edu>
Content-Type: text/plain; charset=iso-8859-1
--- Jonathan Farrugia <jfarrugi@UMICH.EDU> wrote:
> if you didn't line bore the case that is most likely your problem thinks
> me.
>
> jonathan
>
> On Sat, 5 May 2007, Thomas Pfrommer wrote:
>
> > Dear VW community,
> > I know this is a well-discussed problem
Thomas:
Just about two weeks ago I too experienced low oil pressure warning light blinking
problem after driving on the freeway for 5 to 10 miles. The warning light would begin
to blink when I came off the freeway and came to a stop waiting for traffic signal
to go green. Besides, my hydraulic lifter noise became very loud. The noise would
go away after I rev'ed the engine up and down a few times. But the low oil pressure
light would continue to blink or even stayed on when the engine was idling.
I searched the list archive and found the same article about rod bearing getting
out of round and created excessive clearance to cause oil pressure to drop. I was
kind of shocked and feared that my 84 Vanagon with 150K original miles was near
the end of its usable life.
Guess what? I had the problem fixed and it had nothing to do with any rod bearing
clearance at all.
I had my 84 Vanagon in NOP for the past 4 years parked on my drive way. During the
4 years I only started the engine once every month or two for a few minutes. Before
I put it in NOP it was still driven almost daily without ever seeing the warning
light blinked once.
It turned out that after 4 years in NOP my heater valve began to leak. It was located
behind the radiator and was kind of heard to get to. So I delayed doing anything to
it but kept on topping up the coolant.
Well I had topped up with fresh tap water a few times when I was in a rush. Last week
the engine began to make huge clicking noise. That's after I found the rod bearing
article from the archive. I thought my engine was at a point to throw a rod and make
an extra hole on the engine case. But strangely enough it was still running very well
except the noise. I even began to look around for a replacement engine to buy.
Somehow I decided to remove the belt to silent the water pump and alternator so that
I could listen to the engine noise more clearly. What I found was without the belt
there was no noise!!! It was the water pump that was rubbing against the case inside
that made the noise. So I replaced the water pump and sure enough the noise was gone.
I had correct 40/60 dilution of the coolant now.
Today I drove it to Yosemite and back (300 miles). The low oil pressure light did not
blink even once. I don't know how it has anything to do with water pump. Perhaps when
the water pump was on the way out the engine became too hot although it wasn't shown
on the gauge.
I still had one problem though. I had to drive to Yosemite today with an additional
1.9 engine loosely coupled to my original engine. This loosly coupling means a big
sheet of cardboard on the Vanagon to keep the 2nd engine from destroying the
carpet. I had bought a used 1.9 for less than $100 and kept it on the Vanagon before
realizing the problem with the water pump. Now that the problem is fixed I kind
had to carry the additional engine around. This engine looks a little tired and with
a missing water pump now.
David
__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com