Date: Tue, 23 Oct 2007 17:04:18 -0400
Reply-To: Mike <mbucchino@CHARTER.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Mike <mbucchino@CHARTER.NET>
Subject: Re: Need the two lower studs that secure the transmission to the
engine - No P# in ETKA
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=response
Is that all-thread available in grade 10.8 or 12.9 metric? I doubt it.
Any other 'threaded bar' will be SAE grade 5, which is ok for home use, but
not for automotive use, particularly engine mounting hardware.
This guy's engine almost fell out once already. I'd bet he doesn't want
it to happen againn.............
Mike B.
----- Original Message -----
From: "Zoltan Kuthy" <zolo@FOXINTERNET.NET>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Tuesday, October 23, 2007 2:27 PM
Subject: Re: Need the two lower studs that secure the transmission to the
engine - No P# in ETKA
> You can buy a threaded bar and cut the length you need. File off the
> sharp
> ends. Only, that such threaded bar maybe only available at a specialty
> bolt
> and nut supplier.
> Zoltan
> ----- Original Message -----
> From: "Christopher Gronski" <gronski@GMAIL.COM>
> To: <vanagon@GERRY.VANAGON.COM>
> Sent: Tuesday, October 23, 2007 11:07 AM
> Subject: Re: Need the two lower studs that secure the transmission to the
> engine - No P# in ETKA
>
>
>> Great and is there any dispute on the part number? I found this at
>> GermanSuppy that looks right:
>>
>> http://www.germansupply.com/home/customer/product.php?productid=16855<http://www.germansupply.com/home/image.php?productid=16855>
>>
>> Chris
>>
>> On 10/23/07, Mark Drillock <drillock@earthlink.net> wrote:
>>>
>>> Yes, both lower studs are 97mm M10 for a manual tranny waterboxer case.
>>> I just measured one to be sure.
>>>
>>> Mark
>>>
>>> Christopher Gronski wrote:
>>>
>>> > So that's 2 studs at 97mm each right?
>>> >
>>> > On 10/23/07, *Mark Drillock* <drillock@earthlink.net
>>> > <mailto:drillock@earthlink.net>> wrote:
>>> >
>>> > The short one listed is 76mm so the 97mm should be right.
>>> >
>>> > Mark
>>> >
>>> > Bob Donalds wrote:
>>> >
>>> > > the automatic stud is shorter than the std trany stud
>>> > > 97 MM sounds short
>>> > > Bob
>>> > >
>>> > >
>>> > > ----- Original Message -----
>>> > > From: "Old Volks Home" <oldvolkshome@GMAIL.COM
>>> > <mailto:oldvolkshome@GMAIL.COM>>
>>> > > To: < vanagon@GERRY.VANAGON.COM
>>> > <mailto:vanagon@GERRY.VANAGON.COM
>>> >>
>>> > > Sent: Tuesday, October 23, 2007 9:43 AM
>>> > > Subject: Re: Need the two lower studs that secure the
>>> > transmission to the
>>> > > engine - No P# in ETKA
>>> > >
>>> > >
>>> > >> Chris -
>>> > >>
>>> > >> Actually, these should be studs:
>>> > >> VW # N0146752 - 10 x 97mm
>>> > >> Illustration 3-10, Key #43
>>> > >
>>> >
>>> >
>>>
>>
>>
>> --
>> No virus found in this incoming message.
>> Checked by AVG Free Edition.
>> Version: 7.5.488 / Virus Database: 269.15.8/1088 - Release Date:
>> 10/23/2007 1:26 PM
>>
>>
>
|