Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (October 2007, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Tue, 23 Oct 2007 11:27:59 -0700
Reply-To:   Zoltan Kuthy <zolo@FOXINTERNET.NET>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   Zoltan Kuthy <zolo@FOXINTERNET.NET>
Subject:   Re: Need the two lower studs that secure the transmission to the engine - No P# in ETKA
Comments:   To: Christopher Gronski <gronski@GMAIL.COM>
In-Reply-To:   11dcddf80710231107i754bd271s78c4a6ef2d28ce25@mail.gmail.com
Content-Type:   text/plain; format=flowed; charset="iso-8859-1"; reply-type=original

You can buy a threaded bar and cut the length you need. File off the sharp ends. Only, that such threaded bar maybe only available at a specialty bolt and nut supplier. Zoltan ----- Original Message ----- From: "Christopher Gronski" <gronski@GMAIL.COM> To: <vanagon@GERRY.VANAGON.COM> Sent: Tuesday, October 23, 2007 11:07 AM Subject: Re: Need the two lower studs that secure the transmission to the engine - No P# in ETKA

> Great and is there any dispute on the part number? I found this at > GermanSuppy that looks right: > > http://www.germansupply.com/home/customer/product.php?productid=16855<http://www.germansupply.com/home/image.php?productid=16855> > > Chris > > On 10/23/07, Mark Drillock <drillock@earthlink.net> wrote: >> >> Yes, both lower studs are 97mm M10 for a manual tranny waterboxer case. >> I just measured one to be sure. >> >> Mark >> >> Christopher Gronski wrote: >> >> > So that's 2 studs at 97mm each right? >> > >> > On 10/23/07, *Mark Drillock* <drillock@earthlink.net >> > <mailto:drillock@earthlink.net>> wrote: >> > >> > The short one listed is 76mm so the 97mm should be right. >> > >> > Mark >> > >> > Bob Donalds wrote: >> > >> > > the automatic stud is shorter than the std trany stud >> > > 97 MM sounds short >> > > Bob >> > > >> > > >> > > ----- Original Message ----- >> > > From: "Old Volks Home" <oldvolkshome@GMAIL.COM >> > <mailto:oldvolkshome@GMAIL.COM>> >> > > To: < vanagon@GERRY.VANAGON.COM >> > <mailto:vanagon@GERRY.VANAGON.COM >> >> >> > > Sent: Tuesday, October 23, 2007 9:43 AM >> > > Subject: Re: Need the two lower studs that secure the >> > transmission to the >> > > engine - No P# in ETKA >> > > >> > > >> > >> Chris - >> > >> >> > >> Actually, these should be studs: >> > >> VW # N0146752 - 10 x 97mm >> > >> Illustration 3-10, Key #43 >> > > >> > >> > >> > > > -- > No virus found in this incoming message. > Checked by AVG Free Edition. > Version: 7.5.488 / Virus Database: 269.15.8/1088 - Release Date: > 10/23/2007 1:26 PM > >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.