Last question (I hope) how many nuts and spring washers do I need if I am doing just the two lower studs? Two of each or four of each? More? Thanks Chris On 10/23/07, Dennis Haynes <d23haynes57@hotmail.com> wrote: > > Nuts, N01101011 M10X1.5 Din PC10.9 or greater > > Washer, N0122307 M10X21X1 Spring (Wave) Washer > > > > Good hardware suppliers can also get these. > > > > Dennis > > > > -----Original Message----- > From: Christopher Gronski [mailto:gronski@gmail.com] > Sent: Tuesday, October 23, 2007 7:02 PM > To: Dennis Haynes > Cc: vanagon@gerry.vanagon.com > Subject: Re: Need the two lower studs that secure the transmission to the > engine - No P# in ETKA > > > > OK so I'm apparently missiong more than just the studs. Does anyone have > the PN for the nuts and spring washers? > > > > Chris > > > On 10/23/07, Dennis Haynes <d23haynes57@hotmail.com> wrote: > > Very good point. The factory studs are grade 10.9 and so are the nuts and > plated spring washer. Get the right stuff. I have lost track of how many > broken or loose lower studs I have seen. BTW, most of the time when this > happens the clutch is damaged and the trans front needle bearing is > destroyed. For real fun try it with an automatic. > > Dennis > > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of > Mike > Sent: Tuesday, October 23, 2007 5:04 PM > To: vanagon@GERRY.VANAGON.COM > Subject: Re: Need the two lower studs that secure the transmission to the > engine - No P# in ETKA > > Is that all-thread available in grade 10.8 or 12.9 metric? I doubt it. > Any other 'threaded bar' will be SAE grade 5, which is ok for home use, > but > not for automotive use, particularly engine mounting hardware. > This guy's engine almost fell out once already. I'd bet he doesn't want > it to happen againn............. > > Mike B. > > ----- Original Message ----- > From: "Zoltan Kuthy" <zolo@FOXINTERNET.NET> > To: <vanagon@GERRY.VANAGON.COM> > Sent: Tuesday, October 23, 2007 2:27 PM > Subject: Re: Need the two lower studs that secure the transmission to the > engine - No P# in ETKA > > > > You can buy a threaded bar and cut the length you need. File off the > > sharp > > ends. Only, that such threaded bar maybe only available at a specialty > > bolt > > and nut supplier. > > Zoltan > > ----- Original Message ----- > > From: "Christopher Gronski" <gronski@GMAIL.COM> > > To: < <mailto:vanagon@GERRY.VANAGON.COM> vanagon@GERRY.VANAGON.COM> > > Sent: Tuesday, October 23, 2007 11:07 AM > > Subject: Re: Need the two lower studs that secure the transmission to > the > > engine - No P# in ETKA > > > > > >> Great and is there any dispute on the part number? I found this at > >> GermanSuppy that looks right: > >> > >> > http://www.germansupply.com/home/customer/product.php?productid=16855 > <http > ://www.germansupply.com/home/image.php?productid=16855> > >> > >> Chris > >> > >> On 10/23/07, Mark Drillock <drillock@earthlink.net > wrote: > >>> > >>> Yes, both lower studs are 97mm M10 for a manual tranny waterboxer > case. > >>> I just measured one to be sure. > >>> > >>> Mark > >>> > >>> Christopher Gronski wrote: > >>> > >>> > So that's 2 studs at 97mm each right? > >>> > > >>> > On 10/23/07, *Mark Drillock* < drillock@earthlink.net > <mailto:drillock@earthlink.net> > >>> > <mailto:drillock@earthlink.net>> wrote: > >>> > > >>> > The short one listed is 76mm so the 97mm should be right. > >>> > > >>> > Mark > >>> > > >>> > Bob Donalds wrote: > >>> > > >>> > > the automatic stud is shorter than the std trany stud > >>> > > 97 MM sounds short > >>> > > Bob > >>> > > > >>> > > > >>> > > ----- Original Message ----- > >>> > > From: "Old Volks Home" < oldvolkshome@GMAIL.COM > >>> > <mailto:oldvolkshome@GMAIL.COM>> > >>> > > To: < vanagon@GERRY.VANAGON.COM > >>> > <mailto:vanagon@GERRY.VANAGON.COM > >>> >> > >>> > > Sent: Tuesday, October 23, 2007 9:43 AM > >>> > > Subject: Re: Need the two lower studs that secure the > >>> > transmission to the > >>> > > engine - No P# in ETKA > >>> > > > >>> > > > >>> > >> Chris - > >>> > >> > >>> > >> Actually, these should be studs: > >>> > >> VW # N0146752 - 10 x 97mm > >>> > >> Illustration 3-10, Key #43 > >>> > > > >>> > > >>> > > >>> > >> > >> > >> -- > >> No virus found in this incoming message. > >> Checked by AVG Free Edition. > >> Version: 7.5.488 / Virus Database: 269.15.8/1088 - Release Date: > >> 10/23/2007 1:26 PM > >> > >> > > > |
Please note - During the past 17 years of operation, several gigabytes of
Vanagon mail messages have been archived. Searching the entire collection
will take up to five minutes to complete. Please be patient!
Return to the archives @ gerry.vanagon.com
The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.
Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.