Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (November 2007, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Tue, 6 Nov 2007 12:19:14 -0800
Reply-To:     Jake de Villiers <crescentbeachguitar@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Jake de Villiers <crescentbeachguitar@GMAIL.COM>
Subject:      Re: (Part II) Clutch Dies in Cold Weather
Comments: To: neil N <musomuso@gmail.com>
In-Reply-To:  <c4e7c5f90711060850m159c7000kad3ed2f5971d08f8@mail.gmail.com>
Content-Type: text/plain; charset=ISO-8859-1

Maybe the slave is full of water, brake fluid being hygroscopic and all. I just assumed that the fluid in the slave would have been checked right away.

Do a little test bleed and see what comes out - if its rusty-looking, bleed the line through.

On Nov 6, 2007 8:50 AM, neil N <musomuso@gmail.com> wrote:

> My .02 > > If clutch worked in warmer weather, then the clutch mechanicals et al, > should be ok. Since cold weather is one obvious change, then look > toward hydraulics (as you are already) > > If no leaks and PO installed parts correctly and bled with correct > brake fluid, my guess would be clutch slave cylinder since the cab of > the bus would be warmer (if heat working!). > > Would the seals in slave cylinder shrink in colder weather allowing > fluid to pass by? > > Anyone? > > Neil. > > > > > > On 11/6/07, Ben Cichowski <cichowski@montana.edu> wrote: > > 25 Degrees this morning - same dead clutch. Yesterday, after it warmed > up to > > 40, I went out and had NO problems what-so-ever with the clutch... > (although > > it still feels a little soft for my taste and can stick in gear a bit if > I > > hold the clutch in too long - another hydraulic clue...) > > > > So, as per my own thoughts and the thoughts of several others on the > list, > > it looks like hydraulics are likely to blame (If I am missing something, > > someone please give a shout! - and by all means, feel free to tell me > I'm > > being stupid and missing something obvious...things tend to stick better > > that way). > > > > I had my wife pump the clutch this morning as I watched the slave. The > Slave > > moved...a very little bit and seemed like it was trying to push the > lever, > > but then, CLICK, the lever pushed back. She kept getting the soft peddle > > syndrome again and again and I noted maybe 1/4 inch to 1/2 inch of > movement > > on the slave. > > > > Unfortunately...I'm not sure this rules out any particular components. I > > guess it could be the slave leaking...it could be the clutch master...I > > guess it could even be something binding in the tranny (but I think > given > > the cold weather...I can safely say it is something hydraulic). > > > > The Slave does NOT LOOK new - it seems a bit rusty for 6K the PO says it > has > > on it...hmmmm.... Also, I forgot to note in the last post that the slave > and > > clutch master cyl were both listed as replaced when I purchased the > vehicle. > > > > Even thought the master cyl looks new (compared to the slave), my gut is > > still leaning that direction. What do you all think? I've got to get > going > > on it pretty quickly, as the snow will fly any day now and I'm about to > be > > on new-baby duty in a few weeks. > > > > Cheers, > > Ben > > > > > > On 11/5/07 8:48 AM, "Ben Cichowski" <cichowski@montana.edu> wrote: > > > > > Hi All, > > > > > > Thought I had this fixed...20 Degrees F this morning tells me > otherwise! > > > > > > My clutch goes to the floor in cold weather (usually below 40 F). I > thought > > > it was air or moisture in the lines, so I had it pressure bled and > replaced > > > with new hydro fluid. > > > > > > Seems to push down "Dead," then stay there...then it might pop back up > and > > > feel like it has pressure...but pushing it down again does nothing. > > > > > > The PO had put a new slave cyl, and pressure plate in about 6K ago - > maybe a > > > bad part?? > > > > > > > > > Any ideas from you seasoned vets would be great - Thanks, > > > > > > Ben > > > 88 Wofsburg Weekender ej22 (KEP adaptor) > > > > > > > > -- > Neil Nicholson. 1981 Air Cooled Westfalia - > "Jaco" (Bustorius) > > http://web.mac.com/tubaneil >

-- Jake 1984 Vanagon GL 1986 Westy Weekender "Dixie" www.crescentbeachguitar.com http://subyjake.googlepages.com/


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.