Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (May 2008, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Mon, 5 May 2008 12:59:09 -0400
Reply-To:     fitzr@SUSCOM-MAINE.NET
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Doug Fitz-Randolph <fitzr@SUSCOM-MAINE.NET>
Subject:      Re: Parking brake adjustment, '82
Comments: To: Jake Beaulieu <jake_beaulieu@yahoo.com>
In-Reply-To:  <821495.40456.qm@web36403.mail.mud.yahoo.com>
Content-Type: text/plain; charset=ISO-8859-1

Yes, odd, huh? I looked on ETKA and on-line at pictures of the cable, and I think I may have an explanation. On the brake backing plate is an angled 'ferrule' or 'stop', for lack of a better term, that the cable goes through. It appears to slide into place in the backing plate... i.e. you would slide the stop into place, then put the cable through it and attach the end of the cable to the lever on the rear shoe inside the drum.

On mine, the cable ferrule/stops are not seated in the backing plate - they are just pushed up against it when the cable is taut, and loose when it it not. My shoes look to be pretty new... so I surmise that whoever last worked on the brakes pulled the cables all the way out and then for some reason removed the cable stops, and when they reinstalled the cables they slid the stops on the cables rather then seating them in the backing plate then passing the cable through, then finished the brakes. It doesn't look like you can seat the stops with the cable running through them, so I'm guessing they didn't want to disassemble everything again so just left them the way they were. And if it is the guy I think it was, this would have totally been in character for him.

That said, even though the cable stops are not installed correctly, I think my problem might be sticking hardware and/or weak springs. I have a set of springs and hardware which I guess I should just install. I got them from Bus Depot many years ago and never used them - the shoe retaining pins are about 1/4" too short, and the existing pins do not fit through the new retaining pin spring caps, but if I dremel them a little they will. The old caps are totally crusty - one actually popped-off when I moved the shoe.

- Doug

On 5/5/2008, "Jake Beaulieu" <jake_beaulieu@yahoo.com> wrote:

> > >Doug Fitz-Randolph <fitzr@SUSCOM-MAINE.NET> wrote: I'm having a bit of trouble with adjusting the parking brake on my '82. If >has not worked properly since I got the van last year. > >If I look at the cable on the right, it's "hanging out" >of the backing plate, that is, the "spring" part which usually lives inside >the drum is now protruding by about 1/2" and flops freely. Hey Doug, > > I had a similar situation on my 82 westy. The lever that the cable pulls wouldn't return to its "default" position when I released the brake. I tried cleaning and lubrication the lever to no avail. I finally replaced all the hardware (new springs, lever, etc) and it has worked fine ever since. > I find it odd that the spring part of the cable is actually hanging out of the backing plate. The cable was seated very firmly into the backing plate on my van and there is no way that the spring could have protruded out the back. I wonder is a PO put in an aftermarket cable? > > jake > > > >--------------------------------- >Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.