Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (May 2008, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Tue, 6 May 2008 09:00:43 -0700
Reply-To:     Joel VanderKwaak <joelvanderkwaak@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Joel VanderKwaak <joelvanderkwaak@GMAIL.COM>
Subject:      Re: syncro springs on a 2wd?
In-Reply-To:  <481F61ED.6030304@cox.net>
Content-Type: text/plain; charset=ISO-8859-1

That's my experience as well. I have syncro rear springs on my 2wd w/ Porche CV and Syncro OME rear shocks. The front has HD Bilsteins w/ Schwenk springs + a spacer; I may try fitting a set of syncro springs/struts up front while the van is in pieces for a balljoint/control arm update.

On Mon, May 5, 2008 at 12:37 PM, Mark Drillock <mdrillock@cox.net> wrote: > As far as installing goes this is not the case in my experience. You can > put the rear Syncro springs into a 2wd without unbolting the the a-arm > as I have several times. You do for sure need to release the parking > brake and sometimes, especially if a diesel, you need to loosen the cv > bolts on the tranny end a few turns. That said, it is probably a bad > idea unless you use the longer Syncro rear shocks and make sure the cv > angles are ok, which on a diesel they won't be unless you lower the > tranny nose a several inches and this adds other problems. > > Mark > > > > > Chris S wrote: > > > Syncro rear springs on a 2WD Vanagon make for a very stiff ride. I put > them > > on my '85 and found that all my negative suspension travel was gone. The > > Westy bounced over small and medium bumps instead of absorbing them. Part > > of the problem is that Syncro spings have to be compressed to fit. You > > actually have to unbolt the rear A-arm, put int he spring, then compress > the > > suspension by using a jack and reinstall the outer a-arm bolt. So, unless > > you have a GM V6 engine weighing down the back end, don't do it. > > > > If you simply need to lift a sagging rear, I made some spacers from > > polyethylene cutting board. It worked very well. > > > > http://www.knology.net/~vw/vanagon/sag/ > > > > Chris S. > > > > On Mon, May 5, 2008 at 1:46 PM, Brendan Slevin <totorovan@gmail.com> > wrote: > > > > > > > Will a set of syncro springs fit on my 84 gl 2wd? How much will they > lift > > > it, if any? Adverse effects? Thank you! > > > > > > Brendan Slevin > > > 84 GL Totoro > > > Bend, Oregon > > > > > > > > > > >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.