Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (June 2008, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Fri, 6 Jun 2008 14:53:04 -0700
Reply-To:     M'obeechi <obeechi@RUNBOX.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         M'obeechi <obeechi@RUNBOX.COM>
Subject:      Re: Bypass coolant pipes under van for rear heater
Comments: To: kayakjr@COMCAST.NET
In-Reply-To:  <060620082027.23509.48499DCB0003C46400005BD522165279669D06050E970E05@comcast.net>
Content-Type: text/plain; charset="iso-8859-15"

Removing that rear stock heater is an excellent idea - when it leaks it soaks your carpet and the cork-whatever underneath it, then when its cold and damp, water is pulled into your cork-whatever and the carpet, until you clean those things out at a car wash on a hot summer day.

However, I think its better to more the ecu to the hatch area, on the passenger side (the wall), then you can place large batteries on either side under the rear seat, and place a large propex in the center (in an isolated box) and a large inverter can be placed above the propex (a double layer really thin ply, maybe with foam between the plys, should be used to separate the inverter from the propex). This is the only way to have two heavy batteries with balanced load.

Sent: Fri, 6 Jun 2008 20:27:55 +0000 From: John Reynolds <kayakjr@COMCAST.NET> To: vanagon@GERRY.VANAGON.COM Subject: Re: Bypass coolant pipes under van for rear heater

> Goes by the inside diameter, so a 5/8 diameter shoulder, or 5/8 bolt or rod will do it. I was on the fence whether to remove my rear heater after it leaked, but I want the room, don't use the van in winter and didn't want to spend the $100.00 or so to make it all right (new valve, core, etc) > > I plan to take the individual wires out of the 4-wire connector, push them through the floor and then seal them with heat shrink tubing or similar. It's posibble to extend the wiring to something like a closet light or interior light, or water pump if I put a water tank in (I have a weekender) that I can shut off from using the rear blower control on the dash. > > On my weekender, the panel under the froont of the seat tilts backward - I might replace this with a straight up and down wood one to gain some more rear room. > > With a family of 4, there is not enough storage space! > > John > > -------------- Original message -------------- > From: Taeke <taeke.t@gmail.com> > > > Batteries are going where the core is so.... Replacing sounds good, happen to > > know what size to buy? Goes by inside diameter correct ? > > > > > > > > I used two stainless stell bolts that had an unthreaded shoulder under the head. > > I cut the threads off, a nd ground the end witha slight taper to make insertion > > easy. SNIP > > >

----- End Original Message -----


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.